Table of Contents
How are baseboards measured?
Use a measuring tape to calculate the square footage of each room that will need base trim. Add measurements together for each area — such as for the living room, dining room and so on — and divide the number by 12 to determine the linear square feet of each room, as base trim is typically sold in linear square feet.
How do you measure baseboard height?
A general rule of thumb for your baseboards is the 7 percent rule — they should equal 7 percent of the overall height of your room. So, if you have 8-foot ceilings, your baseboards will look best at around 7 inches high.
How do you measure for floor trim?
Measure along the wall and floor junction from the first corner to the first cut point. Record this measurement with an additional note detailing if the left and right sides of the trim are inside or outside angles. Also, note the degree of the angles.
How many linear feet are in a 12×12 room?
Multiply the length times the width of the room to get the room square footage. 12 ft x 12 in/ft (width of the room) = 144 in. So the total linear footage of the 1 x 12 boards is found by multiplying 5 (boards) by 6 (feet) which equals 30 linear feet.
How do you measure linear feet for baseboards?
Divide the total number of inches by 12 to convert from inches to linear feet. For example, if your wall measured 40 inches in length, and you are installing molding on the top and bottom, 40 x 2 = 80 inches. Divide 80 by 12 to get 6.66 linear feet.
How do you measure corners for baseboards?
For inside corners, the long point of the miter is always at the back of the molding, against the wall, and against the miter saw fence. For inside corners, you measure to the long point of the miter and you cut to the long point of the miter.
How do I know how much trim to buy?
Multiply the length times 2 and the width times 2, then add the values together, eg. (length × 2) + (width × 2) = perimeter. Subtract the length of any doors or windows that break up the room. For example, if you have a 36″ entry door to the room, subtract 3′ from the perimeter measurement.
What angle do you cut baseboard corners?
With inner mitered baseboard joints, each baseboard piece is cut at a 45-degree angle. When joined, the two pieces form a 90-degree angle that fits perfectly against the inside corner where two walls meet.
How do you determine the trim angle?
To calculate the proper miter angle for trim-work moldings, simply divide this angle reading by 2. In the example shown, the inside corner is 90.5 degrees—nearly square. The precise miter angle of your moldings should be 45.25 degrees.
How do you determine the angle of a cut?
It’s fine to use a calculator to figure the correct corner angles to cut for shapes with equal sides. The formula involves dividing 360 by the number of sides to calculate the corner angle. Then divide it by two to get the miter angle.
How do you measure and cut angles?
To use this angle measurement to cut the piece of wood, you must divide the actual measurement by two. For example, if you have an inside angle of 90 degrees then you divide this number by two and you get 45 degrees.
What is the most popular baseboard height?
How Tall Should Baseboards Be? Common Heights Sold by Retailers: Retailers sell all sorts of shapes and sizes, but the most common include 3 ¼ inches and 5 ¼ inches. Height of the Walls: Some homes have higher ceilings throughout, while some have lower ceilings in certain rooms.
How tall should baseboards be with 9ft ceilings?
A baseboard height that’s approximately 7% of the wall height provides for a solid and definable base without being too big. The overall proportion of baseboard to wall height will be comfortable and pleasing. So in a room with a 9 foot high ceiling, a baseboard that’s about 8 inches tall works.
What is standard baseboard height?
Here is a great rule of thumb: A standard 8-foot wall typically has a baseboard 3 to 5 inches tall, while a 10-foot ceiling calls for 5 to 7 inches. As a designer, I love adding height for drama. And the taller baseboards create a modern yet elegant finished look.
How much is 40 linear feet?
Add the length measurement of all of the room’s walls. Continuing the same example, 8 + 8 + 12 + 12 = 40 linear feet. This figure represents the linear footage of the room.
How many square feet are in a 12×16 room?
How many square feet are in a 12×16 room? The square footage of a room 12 feet wide and 16 feet long is 192 square feet. Find the square footage by multiplying the width (12 ft) by the length (16 ft).
How do you figure price per linear foot?
How to Calculate Linear Footage Price. Calculating the cost of lumber priced by the linear foot requires finding the total feet needed and then multiplying by the price per foot. Thus, the total cost is equal to the total length in feet by the price per foot.
How much do trim carpenters charge per linear foot?
Wood Trim Costs Item Unit Cost Line Cost Wood trim $4 per linear foot $2,000 Labor (carpenter) $70 per hour $1,680 Total Cost $7.36 per linear foot $3,680.
Is linear feet the same as perimeter?
The perimeter of a room or a fenced area is often measured in linear feet. To arrive at the total linear feet of a room, take the measure all four walls and add them to obtain the linear feet.
How much does it cost in labor to install baseboards?
The labor cost to install baseboards is $4.90 to $7.75 per linear foot. Baseboard materials are pretty inexpensive (only about $0.80 to $1.20 per linear foot). Labor makes up most of your price.
How do you cut a 90 degree corner trim?
To form a 90-degree corner angle, you want to set the miter saw to 45 degrees. Using a compound miter saw, which is made specifically to cut molding, will aid in making the cut perfect. Set the molding into the miter saw upside down and backwards in order for the cut to work.
