Table of Contents
Follow these simple steps: First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
How do I reset my furnace lockout?
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
What causes a furnace to go into lockout?
If fuel pressure is too low or if the temperature in the heat exchanger is too high, the switch closes. This tells the furnace to shut down and go into lockout mode. Sometimes a dirty air filter can reduce air flow through the furnace to a point where the heat exchanger limit switch trips.
Where is my furnace reset button?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
Will a furnace reset itself?
If your furnace isn’t working, you don’t have to call a professional — at least not yet. There is a simple, do-it-yourself furnace reboot process that may get your system back up and running again. Fortunately, restarting your furnace can be accomplished by any adult and the best part, doesn’t cost any money!Feb 8, 2019.
How do you reset a furnace blower motor?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
How do I reset my heating system?
Turn your thermostat “off”, then flip the related circuit breaker “off”. Wait 30 seconds, then turn the breaker back “on,” then the thermostat. Set the thermostat to hot or cold, whichever you prefer, and your desired temperature. This should effectively reset it.
How do you reset a furnace after overheating?
How to Reset Your Furnace Turn down the thermostat to its lowest setting. At the circuit breaker, turn off the power to the furnace. If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on. If the pilot light was out, light a match to relight it.
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
What is a hard lockout?
Hard Lockout: Caused by a failure internal to the control or by a system fault such as flame out of sequence. A Hard Lockout will result in a no heat condition. To reset from Hard Lockout press and hold the “i” button for 2 seconds.
Why is my furnace running but not blowing air?
Check Your Furnace Air Filter Next, check your heater’s air filter, as this can cause a furnace to stop blowing air. Your filter could be so saturated with dust and debris. In that case, even though the furnace is actually blowing air, your clogged filter is blocking it from making it into your ducts.
Where is the reset button?
Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
Why is my furnace not blowing hot air?
First, check to make sure the thermostat is set correctly. You will want to make sure that the fan control is set to auto, and not ‘on’. If the thermostat appears set correctly, turn off your heater at the thermostat and check the filter. If the filter is dirty, replace it.
Should I hit the reset button on my furnace?
The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.
