Table of Contents
Materials Step 1 Rip. I made these plinth blocks just under 4″ wide, so you’ll need to rip a piece of MDF board that wide. Step 2 Stack the Flat-Stock. Step 3 Cut to Length. Step 4 Shave. Step 5 Bevel. Step 6 Sand and Round. Step 7 Install. Step 8 Install Door Trim on Top.
What size should plinth blocks be?
The plinth block should always be at least 2 to 3 inches taller than the baseboard, it must be thicker than both the casing and the base. It should be 1/4 inch wider than the casing.
Why do plinths block?
Decorators and homeowners utilize plinth blocks to improve the look of a room or home. Plinth Blocks create a beautiful conversion between the door casing and baseboard trim work by preventing unsightly seams and angles. They allow smooth transition between materials while adding character and depth to the area.
How do you size a plinth?
Sizing Your Plinth [The Golden Rule] For a Plinth block to look right, it needs to clear the baseboard and base cap height. The other issue is proportion. Plinth blocks look best, when the height is 1.5 to 2 times the width. Many designers follow the “golden rule” which is to make the height equal 1.6 the width.
What is a plinth Moulding?
A plinth block is a decorative moulding block installed at the bottom of a casing. A plinth block is usually thicker than a casing, and can help to enhance the appearance of casing.
What are plinth blocks made of?
To put it simply, a plinth block is a small piece of MDF (can be a different material if required). They are often thicker and taller than a skirting board and thicker and wider than an architrave.
What is IKEA plinth?
Toe Kick: Also called a plinth by IKEA, this is a narrow strip of plastic that covers up the legs; these serve the same purpose as toe-kick boards found on conventional cabinets.
Do you need a plinth?
Modern homes Homes built within the last 20 years usually have flatter walls, which in most cases allow your skirting board and architrave to sit flush. If you have a simple profile, then you probably won’t need a plinth block. Caption: skirting board and architrave join without a plinth block.
What is a concrete plinth?
A concrete plinth is a reinforced concrete beam that is constructed between the wall and its foundation. Concrete plinths prevent the extension or propagation of cracks from the foundation into the wall above and they distribute the load of the wall over the foundation evenly.
What is an architrave block?
Architrave blocks are used to form a decorative corner where architraves meet. Wickes Light Hardwood Architrave Block Moulding – 89mm x 89mm added to “My Project List”.
What paint to use on plinths?
Wooden plinth perfectly tolerates acrylic, alkyd and oil paints. It also varnishes and impregnations fit well. Skirting of polyurethane and foam requires a special approach since this material does not tolerate the ingress of any solvents. In this case, use only acrylic, latex or water-based paints.
Is architrave thicker than skirting?
Generally, architrave is thicker than skirting boards. Plinth blocks are a great way to create a clean transition between skirting and architrave. A plinth block will be thicker than both the skirting and architrave, and when installed really helps to create a more traditional feel.
How are Kickboards attached?
Place your kickboard underneath your cabinets, flush up against the legs. Remove the kickboard and drill pilot holes for the screws using the line marked out in the previous step. (Drilling two holes per cabinet should be sufficient) Reinsert the kickboard and screw it into place.
How high is a kitchen plinth?
As we’ve touched on above, the standard height for a kitchen worktop is about 910mm, measured from the floor to the top of the worktop. We get this figure from totting up the measurements of the following components: The plinth (150mm).
What is the difference between a base cabinet and a sink base cabinet?
A base cabinet will have drawers at the top. A sink base will have drawer fronts only for decoration, but not functional.
Do kitchens need Kickboards?
Kickboards are the foundation of every kitchen. They have one job, and that is to support the weight of everything on top of them. This weight is usually made up of: stone or laminate bench tops.
Why do Kitchens have a plinth?
Plinth in a kitchen serves a more practical purpose. It is there to hide the feet of the base cabinets and stop any debris from going underneath the cabinets. It also helps to create a more solid-looking and neat finish to a kitchen, connecting the cabinetry to the floor.
Why do Kitchens have Kickboards?
The wooden kickboards help to lift the cabinets and island to give more depth to the whole room.
What’s the normal height of a door?
Standard Interior Door Height It needs to be a minimum of 80 inches (although some codes allow for 78 inch doors). Doors that have a height of 80 inches are 6 foot, 8 inches in measurement, which is the reason standard interior doors are known as “6/8 doors.” A 78 inch door would be called a 6/6 door.
Is a corner block good?
Corner block homes have many advantages; they have more access points, more opportunities for windows in the home, more spots for parking, and bigger gardens. Plus, because the corner block is so open and versatile, it gives architects the opportunity to play with different architectural styles in the design stage.
How do you cut a plinth?
To cut down the plinth, measure the height between the cabinet and floor and mark the plinth appropriately (on the side that won’t be visible) before trimming it with a jigsaw. Usually it’s best to cut the plinth 2-3mm shorter than the height between the cabinet and floor to make it easier to fit or remove them.
