Table of Contents
What cord is used for beaded keychains?
Use suede or leather cord for beads with bigger holes, and use wire for beads with smaller holes. You can find all these options at your local craft store. If you want a 5 to 6 in (13 to 15 cm) keychain, cut off 12 in (30 cm) of cord.
How do you make a thread keychain?
How To Make Tassel Keychains Thread the Beads. Thread your beads through the hemp cord as you’d like them. Layer the embroidery thread. Next, take your embroidery thread and slide the wrappers off. Tie the hemp cord around the thread. Cover the hemp cord with metallic string. Trim the embroidery thread.
How do you make a braided keychain?
HOW TO MAKE A FOLDED BRAID KEYCHAIN Cut three pieces of cord a little more than twice as long as you want the finished custom keychain. Stack them, even the strands, and wrap one end with a small rubber band a few inches from the ends. Do a simple braid. Loop one end through the keychain.
What is needed to make keychains?
Supplies Needed: EasyCast Clear Casting Epoxy. Mold Conditioner and Release Spray. Measuring Cups and Stirring Sticks. Disposable Gloves. Jewelry Mold. Small Flowers, pressed and dried (can do it yourself or find them online) Jump Rings. Jewelry Chain.
What is crimp bead?
Crimp beads are soft metal beads used in place of knots to secure clasps and beads onto un-knottable stringing material such as beading wire. To use crimps, you will need some flat nose pliers to squash the crimps, or speciality crimping pliers that “fold” the bead into a small volume. First, thread crimp onto wire.
How do you make keychains with names on it?
How to make name keychains: Write the letters of the name on the square wooden beads. Place your beads in order of the name, since you’ll be threading it backwards. Thread a piece of embroidery floss, knot the bottom, and add a round bead. Thread on your name backwards!.
How do you make a fabric tassel keychain?
DIY Fabric Tassel Key Chain Cut or tear strips of fabric that are 1/2″-3/4″ in diameter by 10″. You’ll will need about 15 of them. Send each of the strips through one of the key rings. Fold them in half. Once you have the strips arranged, send a needle and thread through them to secure. Trim any stray strips.
What is plastic gimp?
Gimp is a narrow ornamental trim used in sewing or embroidery. It is made of silk, wool, polyester, or cotton and is often stiffened with metallic wire or coarse cord running through it. The name “gimp” has also been applied to the plastic thread used in the knotting and plaiting craft scoubidou.
What kind of resin do you use for keychains?
Crafting with epoxy resin can seem a little intimidating at first, but with Color Pour Resin, it’s actually pretty easy. In this tutorial, you’ll learn the tips and techniques needed to create your own customized monogram resin keychain.
How much resin do I need for keychains?
Mix 15 ml total of the Resin Obsession super clear resin (resin + hardener). You don’t need much for this first layer of resin. You only want enough to fill the paw pads plus a little bit more.
How much does it cost to make key chains?
Normally keychain retail prices range from $7 – $20. Pricing should depend on the base cost of your keychains and how much you think your audience will pay for this custom product.
What size beads to make blessing beads?
For the large blessing beads I used about 36 – 1″ beads.
What are welcome beads?
WELCOME BEADS are a symbol to family, friends, and guests they are welcome in your home. Handmade in the Lowcountry of South Carolina by Shannon Levin and Family.
What is the difference between a crimp bead and a crimp tube?
Crimp Tubes The tubes tend to be stronger than crimp beads and less likely to crack and break. Tubes may do a better job of gripping beading wire because they tend to have a larger interior surface area.
What can I use instead of crimp beads?
An alternative to crimp beads and crimp tubes is a newer finding called Screw-Tite Crimps™. Screw-Tite Crimps not only secure your Accu-Flex® beading wire to your clasp, they also allow you to change your clasp for a different one, should you want a different look.
How do you tie off a bead keychain?
Loop the cord through the key ring until the ends of the leather are even. Then, slide the bead through the ends of the cord, up to the top. Repeat with beads until you have filled the cord to the length you desire. Tie off at the end of the beads in a double knot and cut any excess cord.
Can a Cricut make keychains?
Use up scraps when you learn how to make keychains with Cricut! And since it’s a small craft, you can make it on any Cricut smart cutting machine – even the Joy!Aug 13, 2021.
How much cord do you need for macrame keychain?
You can do a variety of styles with just a few materials and 8 yards of macramé cord. These make great gifts and are easy enough to do in a short period of time! Plus, you may have leftover craft material to repurpose into a cute keychain.
What is lanyard string called?
The most common kind of thread used for the craft is flat and comes in many colors, sometimes called “gimp thread”. Another kind of scoubidou thread is supple, round and hollow plasticized PVC tubes usually about 80 centimetres in length.
What is lanyard string?
Plastic Craft Lace Lanyard String is an extruded flat PVC vinyl plastic cord made for craft and hobby applications. You can use this plastic lace to make key-chains, lanyard necklaces, gimp bracelets, key fobs, lanyards,earrings, zipper pulls, jewelry, and much more.
How much resin will I need?
General rule for epoxy coverage For coating epoxies, one mixed gallon (half a gallon each of resin and hardener) will cover twelve square feet at a thickness of 1/8 of an inch. This may vary by brand though, so always check the manufacturers instructions to be sure.
