Table of Contents
How do you build outdoor stairs for a deck?
Can I use deck boards for stairs?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
What size boards do you use for deck stairs?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings.
How do I anchor my deck stairs to the ground?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
Can stairs be built without stringers?
A traditional staircase built with stringers can be less than optimal for very wide stairs. Box steps instead are the preferred choice because they are simple and can be built to any length. If your deck is low and requires only a few stairs or even just one, then steps without stringers are the way to go.
Do deck stairs need footings?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
What is code for deck stairs?
Requirements for Deck Stairs Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back.
How deep should deck stairs be?
The maximum height of a single step is 7.75 inches, and all stair heights must be within 3/8 inch of each other, to keep the stairs regular. The depth (also called tread or run) of each step should be a minimum of 10 or 11 inches depending on the type of stairs.
How thick should stair treads be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
Can I use 2×12 for stair treads?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What can I use for stair treads?
What Wood Is Best for Stair Treads? Oak Stair Treads. Oak is a common type of wood for stair treads. Hickory Stair Treads. Hickory is another common choice for wood stair treads. Maple Stair Treads. Maple’s tan and white hues make it a popular choice for a range of wood products. Poplar Stair Treads. Walnut Stair Treads.
Do deck stairs have to land on concrete?
Stair landings must be at least as wide as the stair and at least 3 feet deep. On the other hand, solid, flat, and stable materials, such as concrete, flagstone, pavers, or brick, can be installed with a measurable slope and will not usually shift under the weight of an off-balance person completing a stairway descent.
How long can stairs be without support?
The minimum recommended size for a deck stair stringer is 2×12, which has a maximum recommended unsupported span of 6 feet. Often this maximum span is dangerously exceeded, resulting in overspanned stringers that will deflect and cause the connection at the deck to pull loose and fail.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
What is difference between steps and stairs?
Both refer to a series of steps—those “structures consisting of a riser and a tread,” as the definition of step puts it. When they’re outside, they’re more often called ‘steps’ than they are called ‘stairs. ‘.
What is a cascading staircase?
Cascading stairs are a popular style of staircase that wraps around the corner of a low deck. This is an attractive and extremely functional approach to deck design and stair construction. Remember that cascading or wrap around stairs are designed to flare out and increase in size towards the ground.
How do you build 3 sided deck stairs?
The trick to creating a three-sided staircase is to make bevel cuts on some of the stringers where they meet at the corners. The riser boards also get beveled, and the stair treads are mitered to help it all go together. The stairs have a post-and-railing system that matches the railing assembly on the deck itself.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
How long can deck stairs be without a landing?
A flight of stairs should not rise vertically more than 147 inches without a landing. An intermediate landing is a small deck, and should be built as such, including appropriate footings, posts, and bracing.
