Table of Contents
How do you build 3 sided deck stairs?
The trick to creating a three-sided staircase is to make bevel cuts on some of the stringers where they meet at the corners. The riser boards also get beveled, and the stair treads are mitered to help it all go together. The stairs have a post-and-railing system that matches the railing assembly on the deck itself.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How many stringers do I need for deck stairs?
Deck Stair Basics Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What size wood do you use for steps?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads.
Can you buy premade steps?
You definitely can buy premade deck stairs. Whether you’re looking for a large project option or a quick fix, there is an option for you out there. Premade deck stairs can be bought at any place that sells premade stair kits like Paragon Stairs, the same as other stair types.
Can you make stringers out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How thick should a stair stringer be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
How far apart can stair stringers be?
Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers. The maximum 18-inch spacing presumes treads of 5/4-inch wood decking or 2-by stock.
Can I use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
Can I use 2×4 for deck steps?
Either way, 2x4s as deck joists are safe as long as your design doesn’t span too far or include guard rails or stairs. The other main limitation is the size of your deck. 2x4s are the smallest dimensional option, making them great for low, ground-level decking if they’re spaced no further than 12” on center.
Do deck stairs need a landing?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
How tall is a 2 step Stringer?
Size:2 In. Step stringers are cut for 2″ X 12″ Treads, and have a 7″ Rise.
How do I figure out how many steps I need?
The vertical distance between the floors to be linked by the staircase is the principal determinant of the riser and tread dimensions. You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14).
