Table of Contents
Can I use 2×10 for stair stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How do you calculate stair stringers?
How do I calculate a stair stringer? Start by finding the overall height that the staircase will be. Decide the height or “rise” you’ll want for each step. Divide the total height of the staircase by the height or “rise” you want for each step.
How far apart can stair stringers be?
Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers. The maximum 18-inch spacing presumes treads of 5/4-inch wood decking or 2-by stock.
Do you use 2×10 or 2×12 for stair stringers?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
Can I use 2×12 for deck stair treads?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
How many steps is a 4 foot high deck?
A four-foot high deck can have a range between 6 and 8 steps.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
How do you attach stringers to a deck?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
Can you use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
How many stringers do I need for deck stairs?
Deck Stair Basics Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in.
How long should a 2×12 stringer be?
How to Use the EZ Stair Calculator. We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
What size are deck joists?
Commonly used joist sizes are 2-by-6, 2-by-8 and 2-by-10. For example, when you space joists 16″ apart — which is standard for residential decks — a deck spanning 9 1/2′ would require 2-by-6 joists, a 13′ deck would need 2-by-8 joists and a 16′ deck calls for 2-by-10 joists.
What is the code for outdoor steps?
Exterior Stair Construction The rise of the stairs should be between 125 mm (5”) and 200 mm (8”). This is measured from top of a tread nosing to the top of the next tread nosing or landing. The run should be between 210 mm (8 ¼”) and 355mm (14”). Unit run is measured from face of nosing to face of nosing.
What is building code for stairs?
The IRC stairs code states that, to comply with stairway requirements, the minimum width for residential stairs be no less than 36 inches. The stair riser code is up to 7.75 inches, and can not vary more than 3/8 of an inch. There are also section codes in place for standard stair tread dimensions.
How deep should a deck step be?
The maximum height of a single step is 7.75 inches, and all stair heights must be within 3/8 inch of each other, to keep the stairs regular. The depth (also called tread or run) of each step should be a minimum of 10 or 11 inches depending on the type of stairs.
