Table of Contents
Trace your coasters with the pencil directly onto the paper and cut just inside the line. Add a medium layer of Mod Podge to the coaster and then lay the paper down and smooth, smooth, smooth. Keep smoothing until all of the bubbles are removed and let dry for 15 – 20 minutes. You don’t have to use Outdoor Mod Podge.
How do you seal coasters with Mod Podge?
Instructions Cut square pieces of paper to fit the tiles using scissors. Add a layer of Mod Podge to the top of a tile; place the paper down and smooth. Using the stamps, stamp out the names/date/etc. Seal each tile with 2 – 3 coats of Mod Podge, letting dry between coats. Trim cork to fit the back of the coasters.
How do you make Mod Podge coasters not sticky?
Here’s what you need to do for sticky Mod Podge. Purchase a clear acrylic sealer such as this one. When you are done with your project, allow it to dry for time recommended (about 24 hours after the last coat). Spray a coat of sealer, allow to dry for 15 minutes, then spray another coat.
How do you seal homemade coasters?
Apply 2 coats of a clear spray sealer to the coasters to seal and waterproof them. Make sure to do this in a well ventilated area. Spray the top, sides, and bottom side. Let the sealer dry for 20 minutes or so.
Is Mod Podge good for coasters?
Okay Mod Podgers, it’s time to pull out your Hard Coat Mod Podge! This Mod Podge is water resistant and not tacky, just right for coasters. Paint a thin coat of Mod Podge onto your tile. I used a soft bristle brush, but you could use a foam brush, too.
Is Mod Podge clear acrylic sealer waterproof?
Protect all decoupage creations with a dust and fingerprint-resistant spray finish . Mod Podge Clear Acrylic Sealers can be used over water-based and oil-based paints, glazes, lacquers and varnishes . They dry clear, are waterproof, and non-yellowing .
How do you waterproof Mod Podge?
No, Mod Podge is not Waterproof. It can take a few drops of water but if you want to make your project truly waterproof, then you need an additional sealer. Depending on your Project I would Recommend Varnish, liquid epoxy or an enamel sealer.
How do you heat proof coasters?
If you like, you can sand very lightly using some fine wet and dry sandpaper in between layers to help get rid of any brush marks. Finally seal your coasters with two or three coats of acrylic spray or varnish, or you could try using a clear engine lacquer which is heat resistant and helps stop hot mugs from sticking.
What do you put on the bottom of coasters?
As a final touch, attach felt squares to the bottom of your coasters with glue or double sided tape. Some craft stores even sell adhesive-backed felt which makes it super easy. You could also use cork-board instead of felt.
How do you make decoupage coasters waterproof?
You’re going to want to coat the image and coaster with at least three coats of Mod Podge, allowing it to dry for 15 minutes (or until clear) between coats. Once the final coat has dried, spray all of the coasters with a clear acrylic gloss spray, which ensures that they’re waterproof/drink proof.
Is Mod Podge waterproof?
Well, there are a few things you should know about this formula. First of all, Mod Podge Outdoor is not waterproof. It is HIGHLY water resistant. This means that if you want a decoupage item to sit on a covered porch where it is not exposed to weather 24 hours a day, you are fine using this formula by itself.
Is Mod Podge fire resistant?
A: It’s very safe! The key is keeping the Mod Podge on the outside of the jar. Mod Podge isn’t flammable, but you want it on the outside of a jar and not near a flame so it doesn’t melt.
Is Mod Podge acrylic sealer heat resistant?
Yes, Mod Podge is somewhat heat-resistant. Mod Podge won’t last long on an object which experiences high heat regularly. Also, Mod Podge can’t take oven heating at all. Mod Podge is applied onto surfaces to protect them from UV rays.
How do I make tile coasters?
Step 1: Cut the Paper. Cut your paper, or photos, to 3.5″ square. Step 2: Glue Paper to Tile. Using the Mod Podge and brush, glue the scrap book paper to the center of a tile. Step 3: Apply Mod Podge over the Top. Cover the top of the tile with a layer of Mod Podge. Step 4: Cut & Apply the Felt. Step 5: Seal the Coasters.
What can you make coasters out of?
For these colorful coasters, the supplies needed are: scrapbook paper, mod podge, fabric glue, clear acrylic glaze, felt, a sponge brush and ceramic tiles. Glue the paper to the tile and let it dry completely. Then paint over the paper and tile with mod podge. Let it dry and repeat 2 or 3 times.
Can Modge podge be used for outdoor projects?
Perfect for protecting crafts that may be outside and exposed, Mod Podge Outdoor holds up to the elements, rain or shine. This unique sealer, glue and finish can be used on wood, terra cotta, slate, tin and more, and it cleans up easily with soap and water.
What is the best way to apply Mod Podge?
When applying Mod Podge over a design, apply one layer of the Mod Podge with side-to-side brush strokes. Allow that coat to dry for 20 minutes or so before applying another even layer of Mod Podge in up-and-down strokes. I have found that this process results in the smoothest possible finished surface.
Does Mod Podge yellow over time?
Yes, it does yellow over time. But it takes a long time, and it’s very slight. I’ve had things for years that are not yellow.