Table of Contents
How do you calculate stair stringers?
Take the total height of your stairs divided by the number of steps. This will give you the exact height you should cut each rise in your stair stringer boards.
Can you use 2×10 for stair stringers?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What size lumber is used for stair stringers?
Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.
Can I use 2×8 for stair stringers?
You should attach 2×6 or 2×8 support framing under the rim flush to the bottom of the stringer. The stairs will hang here. Install a piece of blocking below the rim joist to extend the attachment surface for your stairs stringers. Use a level to mark the top step.
How far apart do stair stringers need to be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
Can I use 2×12 for stair treads?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
How long should a 2×12 stringer be?
cut stringers. The two most common cut-stringer defects that I see are overspanning and overcutting. The minimum recommended size for a deck stair stringer is 2×12, which has a maximum recommended unsupported span of 6 feet.
How long of a 2×12 do I need for stairs?
We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths. Either B or C is required.
Can you use joist hangers for stair stringers?
Use joist hangers to fasten the blocking. Pros: Allows for the use of all types of stair stringer hangers. The top of the stair stringer acts as the first tread instead of being flush with the deck’s surface.
How thick should a stair stringer be?
The thickness of your plywood stair treads should be anywhere from 1” to 1 ½” in thickness. It’s important to invest in quality plywood. As a rule of thumb, always remember that the fewer stairway stringers you use, the thicker you want your stair treads to be.
Can I use plywood for stair treads?
While ¾” thick plywood or OSB is considered sufficiently thick for subfloors, it is not uncommon to use a thicker material for the stair treads. One inch of total plywood thickness is ideal and can be made from two layers of ½” plywood, bonded together.
What kind of wood should I use for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has . 60 RET level.
Are stairs 45 degrees?
For most standard stairs, the stair angle varies between 30 degrees and 45 degrees. Egress stairs have a shallower angle around 30-35 degrees while industrial stairs have steeper angles ranging from 40 to 70 degrees.
How tall is a 5 step stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in. x 11 in. x 60 in.).
What is a good rise and run for stairs?
Over the years, carpenters have determined that tread width times riser height should equal somewhere between 72 to 75 inches. On a main stair, the maximum rise should be no more than 8 1/4 inches and the minimum run should be no less than 9 inches.
How tall is a 4 step Stringer?
Mendocino Forest Products Stair Stringer 4 step Redwood (Common: 48 in. x 12 in.; Actual: 1.5 in. x 11 in.
How do you calculate stair landing?
The height of the landing is determined by where it is located along the stair run. In this design, since it is half way from the top level, it is 8 steps high (8 x height of each step (6 7/8) equals 55 inches). The horizontal positioning of the mid-level landing is determined by the number of treads on the stair run.
How far should stair tread overhang riser?
Stairs must have an overhang between 3/4″ to 1-1/4” to increase the depth of the step, making it better for descent while maintaining a clear 10-inch going for the ascent. Treads that are 11-inches deep or greater do not require an overhang.
