Table of Contents
How do you make an envelope pillow cover with one piece of fabric?
Instructions Wash the fabric. Cut the fabric to pillow size. Create a double-fold hem on smaller ends of cut fabric. Overlap the fabric to give you the size of the pillow form, pin, and sew a 1/2″ seam. Trim corners then turn fabric right side out. Then insert the pillow form into the pillow cover and enjoy!.
How do you make a simple cushion cover?
Step by step Cut a square of paper the same size as your cushion pad. Iron your fabric thoroughly before you cut it to get rid of any creases. Take a good look at the fabric’s pattern and choose a section you like for the front of the cushion. Pin the other pieces of paper to your fabric and cut around them.
What size zipper do I need for a 20 inch pillow?
For example, I use a 18” zipper for a 20” pillow insert and a 22” zipper for a 24” pillow insert, etc. and I always sew my covers 1 inch smaller than the insert (the seams for a 20” pillow insert are actually 19” for the pillow cover) so a zipper that is two inches smaller than the size of the insert works best.
How much should an envelope pillow overlap?
Basic Instructions: The ends will overlap approximately 3″ at the back when finished. This extra fabric is to ensure that the pillow form will be hidden when the pillow cover is in place. To calculate the fabric measurement you will need measure your pillow insert.
What is an Oxford pillowcase?
What is an Oxford Pillowcase? An Oxford Pillowcase often has an opening at the back where the pillow is inserted and it’s famous for having a decorative border of various shapes and sizes. It’s usually mistaken to be larger in size because of its wide-stitched flat hem.
What kind of zipper do you use for pillows?
Zipper which is 3 inches (7.5cm) shorter than your pillow inserts. Remember, zippers are measured along their teeth and not along the tape. Plastic (nylon coil) zippers are better for cushion covers than metal ones as they are smoother and easier to sew.
What is an invisible zipper?
An invisible zipper is a zipper that is hidden within a seam. An invisible zipper is sewn in a different manner than other visible zippers. With an invisible zipper, you do not need to bother with topstitching on the finished zipper, but rather you install the zipper before the seam it is installed in is sewn.
What size pillow goes in a 16×16 cover?
We recommend an 18″ x 18″ insert for our 16″ x 16″ inch throw pillow covers to get a plump pillow.
How much fabric is needed to cover a 16×16 pillow?
Sizing Up Fabric Needs for Pillow Covers Dimensions (Length by Width) Amount of Fabric Needed for 1 Pillow Cover (Using 54-inch Wide Fabric with No Pattern Matching) 14 x 14 inches 1/2 yard 16 x 16 inches 1/2 yard 18 x 18 inches 5/8 yard 20 x 20 inches 3/4 yard.
How much fabric do I need for a 20×20 envelope pillow?
You will need 3 pieces of fabric for these pillow covers. Start by measuring your pillow to determine what sizes of fabric you’ll need. First panel: Add 1 in to the width and height of your pillow measurement. For example, if your pillow is 20×20, you will cut a piece of fabric 21×21.
What is an envelope pillowcase?
What are Envelope Closure Pillowcases? Traditional pillowcases are open on the ends. An envelope pillowcase has a special envelope closure at the end of the case, so the pillow is tucked in and out of sight for a more finished look when making up the bed.
What do you stuff a pillow with?
10 Top Types of Pillow Stuffing Down Pillow Stuffing. Image Source: Terry Cralle. Feather Pillow Stuffing. Image Source: Terry Cralle. Polyester Fiberfill Pillow Stuffing. Image Source: Terry Cralle. Memory Foam Pillow Stuffing. Buckwheat Pillow Filling. Kapok Pillow Stuffing. Cotton Pillow Stuffing. Latex Pillow Filling.
What size should I make a cushion cover?
We recommend: for square cushion covers you use an insert that is about 5-6cm or 2″ bigger than the cover. for rectangular (lumber) cushions you use an insert that is 2-3cm or 1″ larger than the cover.
Can you use hot glue to make a pillow?
Add hot glue to the outer edge of one side of your opening and then fold the fabric over to make it match up with the rest of the pillow. Be sure to tuck your corner in before securing the edge so you don’t have an uneven edge sticking out! And you’re done!Jul 24, 2013.
How do you glue a pillow to the wall?
Set a carpenter’s level on the top edge of each cushion and adjust the cushions so they’ll be level. Tie each pair of cushion ties in a knot or bow. Hold each tied pair against the wall with the cushions in place. Mark the wall in pencil inside the top of each pair of ties, where a hook will go.
How much fabric is needed to make a lumbar pillow?
One 12- to 14-inch pillow requires a 36-inch square (1 yard). An 18- to 20-inch pillow needs 1 1/4 yards of 54-inch fabric. How much trim: Add up the finished measurements for the four sides plus at least 4 inches for turning the corners and seam margins.
How do you make a pillow out of a jacket?
Step 1: Fold Out Your Jacket. first, fold out the jacket and lay it flat on the ground. Step 2: Fold in Your Sleeves. now, fold in your sleeves. Step 3: Fold the Sides in to the Middel. Step 4: Roll Up the Jacket. Step 5: Fold Your Jacket Into the Hood. Add Tip Ask Question Comment Download. 2 Comments.
What is a Housewife pillowcase?
For those of you who aren’t in the know, Housewife Pillowcases have a sewn edge, which fits snugly to the pillow, and Oxford Pillowcases have a fabric border around the edge, usually around 5cm. They then became known as “Housewife” pillowcases in the co-operatives honour.
What is a square pillowcase?
A continental pillowcase is a square pillowcase, usually 65cm x 65cm, which can come in both Housewife or Oxford design. Continental pillows are usually used either as back pillows set against the headboard or as decorative pillows to dress a bed.
