Table of Contents
PREP THE FRAME. Remove the glass, photo and any cardboard or paper backing from the frame. REMOVE FRAME HARDWARE. CLEAN THE FRAME. SPRAY PAINT THE FRAME. MEASURE THE LENGTH AND HEIGHT OF THE FRAME. CUT CHICKEN WIRE. STAPLE CHICKEN WIRE TO THE FRAME. TRIM AND HAMMER CHICKEN WIRE UNTIL FLAT.
What is the best way to attach chicken wire to wood?
Attach the chicken wire to a good starting point in your frame or fence. To attach it to wood, use the staple gun or fencing staples and run them along the edge of the chicken wire, about every 6 inches.
How do you attach wire to wood frame?
Hold the wire mesh in place, or have a friend hold it for you, and then press an industrial staple gun — with staples slightly smaller than the depth of your frame — onto the top corner of the mesh. Pull the trigger and insert a staple into the top left corner, and then the top right corner.
How do you make chicken wire lay flat?
Drive in stakes where you want the perimeter of the fence. Unroll the first bit of fence and attach it to the first stake. Stretch the fence as you unroll it and tie it to the next stake. Continue, stretching the fence so it stays tight and flat, and making sure to attach it to the stakes as you go.
How far apart is post for chicken wire fence?
Be sure to place your fence posts at least 6-8 inches into the ground so that the soil plate is completely buried. Each post should be placed no more than 10 feet apart.
Can I use a staple gun for chicken wire?
Staple guns are used to fasten fabric and foam to wood in carpeting and upholstery projects. They are also used to fasten a number of materials around your house, such as fastening chicken wire to fence posts or fastening ceiling tiles, shingles, or weather stripping.
How do you attach chicken wire to metal frame?
Slide your fingers (with gloves on) into the holes in the center point of the chicken mesh fencing, just past the next fence post, and pull it firmly to stretch the chicken fencing across the open area. Attach the Hex wire to this part of the frame or post using the staples or wire pieces.
How do you secure a fence wire?
Hold the wire in place on the fence and apply the first staples to the post. Wear heavy gloves for the job to protect your hands from the wire. Unroll a couple of feet of wire, pulling it taut, and then staple to the fence rails. Keep unrolling and stapling, allowing about 24 inches between staples.
How do you secure wire mesh to wood?
The best way to attach mesh fencing to wood posts and rails is with galvanized U-staples. I suggest using staples no smaller than 3/4 inch for this purpose. Roll the fencing from the first post to the second, and then fasten the edge to the first post.
What staples for chicken wire?
Fas-n-Tite 3/4-in Leg x 3/16-in Round Crown 14-Gauge Fence Staples (1-lb) 475 pieces per package. Used to attach poultry netting (chicken wire) to wooden fence posts. Also used to attach insulation and to fasten suspended ceilings to wood framing using wire.
Can you flatten chicken wire?
Flatten your sheet of chicken wire as best you can so there are no waves or bumps. Use a hand stapler or upholstery stapler to secure the chicken wire to the back of the frame. Apply as many staples as needed, making sure to get a staple in each corner and two on each side at minimum.
Does chicken wire need to be stretched?
It’s tempting to just keep unrolling the chicken wire to get the job over and done with. The best approach is to unroll it and stop every 15 to 20 feet to stretch the wire and work out any kinks. It takes longer, but you’ll install a better fence.
How do you build a chicken wire fence?
How to Build a Garden Fence with Chicken Wire Step One: Determine Fence Positioning. Step Two: Dig Holes for Wooden Posts. Step Three: Place Posts in Holes. Step Four: Install Top and Bottom Rails. Step Five: Roll Out the Chicken Wire. Step Six: Staple Chicken Wire. Step Seven: Trim Excess Chicken Wire.
How high should a chicken fence be?
Fences need to be 6 foot tall to keep chickens in and to keep predators out. Fences also need to be buried into the ground at least 6 inches to stop chickens getting underneath them. You should choose heavy duty fence with small holes.
Can fence posts be 10 feet apart?
Typical spacing is right around 8 feet between each post however different circumstances may call for different measurements and it is not uncommon to have spacing between posts reach up to 10 feet. Once you have a rough idea of your post layout start by digging your first hole.
What size t-post do I need for a 4 ft fence?
When figuring out what size T-post to use for a four-foot fence, remember that you will drive the posts about two feet into the ground. This means you need posts that are at least 24 inches longer than how tall you want your fence. For a four-foot fence, you should use T-posts that are at least six feet long.
What is the best tool to cut chicken wire?
Snips are great for cutting thin sheets and wire mesh and are even capable of delicate curves, but you may run into difficulty at lower gauges, particularly if the metal is quite hard. Snips may leave burrs. Hacksaw – Like snips, chances are most DIYers will already have a hacksaw.
Is chicken wire easy to cut?
Besides durability, chicken wire boasts flexibility and is easy to cut. It can be more difficult to cut and install types of fencing with much heavier gauges, such as the similar-looking chain link.
How deep should I bury chicken wire?
Bury the chicken wire or hardware cloth 12 inches deep all along the run to add an additional barrier against burrowing predators.
