Table of Contents
How to Lock Maytag Oven Doors Locate the “Cancel” and “Cook & Hold” buttons on the oven’s control panel. Hold down “Cancel” then hold “Cook & Hold” with another finger for three seconds. Wait three seconds; the display will change from “OFF” to “LOCK” and the door will seal. Repeat these instructions to unlock the door.
How do I lock my oven door?
With the door open, locate the door jamb switch on the face of the oven.Manual Switch: Press the Self Clean pad. Close the oven door. Slide the latch to lock the oven door. Hit the Clear/Off or Cancel button immediately. Unlock the door. The control should now be reset and there should not be a need for service.
How do you unlock a Maytag oven?
Door is locked when starting or using the oven Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
Why does my Maytag oven says lock?
When you place the Maytag oven into self clean mode, the oven door will lock to prevent the door from accidentally being open during cleaning. This is due to the fact that during the cleaning cycle, the oven reaches temperatures far above normal cooking.
How do I lock my oven door to clean it?
For Automatic Lock Doors: Make sure the oven is empty. Touch the CLEAN pad or turn the knob selector to CLEAN on the oven control. After a few seconds the words LOCK DOOR appear on the panel and/or the LOCK light will come on. Touch the CLEAR/OFF pad or turn the selector knob to OFF when the clean cycle is complete.
Why does my oven have a lock?
Most self-cleaning ovens have a lock built in for use during the cleaning cycle. During cleaning, the oven heats up to a very high temperature to burn away any food that has spilled. The oven lock prevents the door from being opened until the temperature has reached a safe level.
Why is oven door locked?
It’s fairly common for the lock function to get stuck if the self-cleaning cycle was interrupted for any reason, like a power outage. If the outlet is hard to reach, you could also turn off the circuit breaker that powers your kitchen. Leave it off for 5 minutes before flipping it back on.
How do I reset my Maytag oven?
Reset power to the product: Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Start a bake cycle. Monitor the oven for one (1) minute to ensure the error code does not display again. Verify oven operation.
How do I reset my Maytag oven control panel?
Make sure the Control Lock function is turned OFF. Some ovens may be equipped with Control Lock. Look for “Control Lock” on the oven control console, then reset by, typically, pushing & holding for 3 seconds.
How do I stop my Maytag oven from self cleaning?
Press the Cancel button to stop the cleaning cycle if necessary. If the door has an automatic lock, it will remain locked until the oven has cooled. If the door has a manual lock, wait at least an hour and a half for the oven to cool before opening the door.
How long does the oven door stay locked after self-cleaning?
A self-cleaning oven is designed with a mechanical interlock (patented in 1982) to keep the oven door locked and closed during and soon after the high-temperature cleaning cycle, which can be approximately three hours. The door stays locked to prevent burn injuries.
How do I fix F9 error on Maytag oven?
How to Remove the F9 Code From Maytag Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. Open the oven door and check the door latch. Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. Press the oven door shut gently. Test the oven.
How do I reset my self-cleaning oven?
Reset the Power Resetting the power for your oven should unlock the door locks. To reset the power, simply turn the power off at the wall for a couple of minutes and then turn it back on or turn the circuit breaker off in your fuse box for a few minutes and then turn it back on again.
Why won’t my oven heat up after self-cleaning?
The most common cause for this could be an open or bad thermal fuse on the back side of the oven. SOLUTION: The only solution for this is to replace the thermal fuse to get the heating elements working again. For this, professional help can be taken.
Why is my oven door not closing properly?
If your oven door doesn’t close all the way or hangs unevenly, several issues could be the culprit. Replace the hinges with identical new ones and hook them back into the hinge holes in the oven. Push the door down to lock the hinges in place, or replace the screws. Check the door springs to see if they are broken.
Can self-cleaning ovens catch on fire?
Fire Hazard. Last but certainly not least, the self-cleaning feature can present a fire hazard. Even if you’ve removed all the larger food particles, you’ll likely have grease or cooking oil splatters and spills to burn off.
