Table of Contents
Turn the gas knob to “Pilot,” press and hold it down. This will start the flow of gas so you can light the flame. Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold. While still holding the gas down, light that pilot.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How do you reset the pilot light on a water heater?
Once the pilot lights, keep holding the knob/button down for around one minute. After that time, slowly release the knob/button and check that there’s still a flame coming from the pilot. Go back to the gas valve and turn the knob to “On.” Usually you’ll hear a noise indicating the main burner is igniting.
Should the water heater be on pilot or on?
You should set the water heater to “pilot”. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
How do I know if my pilot light is out on my water heater?
Three quick ways to tell if your water heater’s pilot light is out are: Your Water is Cold. Blinking Light or Error Message. You Can’t See the Flame.
What causes a water heater pilot to go out?
Your thermocouple senses when your pilot light is burning. If it senses that your water heater pilot light keeps going out, the thermocouple will shift off the gas supply to the heater. Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Is there a reset button on gas water heater?
A water heater reset button, usually red, is located in the center of the limit switch just above the water heater thermostat. The water heater limit switch is a safety device that will shut the power down to the water heater if something malfunctions and the water gets to hot.
Why is my hot water heater not lighting?
If you have a natural or propane gas water heater, chances are the pilot has gone out. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
What causes a pilot light to go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
How do you light a water heater pilot?
Lighting the Pilot Light on an Automatic Hot Water Heater All you have to do is hold the pilot knob down for 30 seconds and hold the ignition button at the same time. You do not need to use a lighter. Your pilot light will turn on!Feb 13, 2020.
Is it safe to light pilot on water heater?
If you’re water won’t heat up, the pilot light on your water heater may have blown out. Lighting a water heater is simple, no matter what type you have. Most newer models of gas water heaters have a simple ignition switch. In just a few steps the water heater is lit, no problem.
What setting should my gas water heater be on?
Know the Ideal Setting: The best setting for gas water heaters is around 115 to 120 degrees Fahrenheit. Oftentimes, water heaters will have additional options to either lower or increase the temperature of the water inside. In the case of the video’s water heater, A, B and C each have an increase of about 10 degrees.
How do you know if the pilot light is on?
If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
What is pilot mode on water heater?
On gas water heaters, the pilot light makes sure that there’s always flame available when the burner needs to kick in and heat water. If you run out of gas, install a new water heater or have to shut it down for some reason, lighting the pilot is the first step to turn on a water heater.
How much does it cost to replace pilot light on water heater?
Pilot light replacement or lighting cost Water heater pilot light replacement costs $50 to $200. The pilot light produces a flame to ignite the gas burner. Plumbers charge $45 to $150 per hour to reignite the pilot light, and the task typically takes 1 hour or less.
