Table of Contents
If you have a gas furnace, here are the steps on how to light a pilot light. First, locate the pilot valve on the furnace. Find the gas valve and turn it to the “off” position. Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How do you light the pilot on a gas heater?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
How do I turn my gas back on after disconnecting?
You are going to need a wrench or gas shut off tool to do this. Very slowly, turn the meter back into the on position. The lever should be in line with the pipe after making a ninety-degree turn. Finally, you can re-light any of the pilot lights in your appliances.
What causes a pilot light to go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
How much does it cost to relight a pilot light?
Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
Do you smell gas when pilot light goes?
Pilot light safety is important to prevent fire or poisoning from natural gas the pilot burns. If you smell the “rotten egg” odor of escaping gas, check to see if the pilot light is extinguished. If it is not, turn the gas valve to the “off” position and call your gas company.
Why is my gas heater not lighting?
There are several possible reasons why your gas furnace pilot won’t light: an ongoing draft, a faulty thermocouple, an accumulation of dirt, or an inefficient supply.
Why is my pilot light not staying lit on my furnace?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Can you manually light a gas oven?
If you don’t have the owner’s manual, open the oven door and look in the bottom of the oven for a small hole marked “Pilot Light” or something similar. If the oven is designed to be manually lit for each use, turn the temperature dial on slowly. The gas should ignite. Remove your hand and the match immediately.
Can you manually light a gas oven with electric ignition?
Question: The ignitor on my General Electric gas stove burned out. Answer: No, this is not possible due to the gas being controlled by the gas safety valve. You need the ignitor to be working properly before gas is allowed out of the gas safety valve.
How do I know if my gas is shut off?
A) located just before the gas meter. This valve, often called the street-side valve, is normally a rectangular nub (Photo 1). When the long side of the nub or handle is parallel to the incoming gas line, it’s open and the gas is flowing. When it’s turned a quarter turn, perpendicular to the incoming pipe, it’s closed.
How do you fix a gas fire that keeps going out?
Easy DIY Fix: Gas Fireplace Won’t Stay Lit Before You Begin: Is Your Pilot Light Lit Inside Fireplace? The Fix: Pilot Light to Gas Fireplace Won’t Stay Lit. Check Your Thermopile Output with the TH/TP Contacts. Don’t Replace Your Thermopile or Thermocouple Right Away. Cleaning the Thermopile. Re-test the Cleaned Thermopile.
Why does pilot light go out on hot water tank?
Your thermocouple senses when your pilot light is burning. If it senses that your water heater pilot light keeps going out, the thermocouple will shift off the gas supply to the heater. Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame.
Is my pilot light too high?
Next to the “Pilot” indicator on the furnace’s control switch, there is a small screw located near the pilot light-thermocouple assembly. If it extends well above the thermocouple, it’s too strong. If the flame covers the top of the thermocouple and burns steadily with a yellow tip, that’s just about right.
Can you manually light a gas hot water heater?
Lighting a water heater is simple, no matter what type you have. Most newer models of gas water heaters have a simple ignition switch. In just a few steps the water heater is lit, no problem. If you’ve moved into an older house, though, you many have the kind of water heater that needs to be lit manually.
Is it safe to light a pilot light?
Is relighting a pilot light dangerous? Relighting a pilot light is potentially dangerous. If the flame blows out, the gas won’t stop coming in the pilot light tube and will continue to escape without igniting. As it continues to collect in your room, lighting it could set off an explosion.
