Table of Contents
How do you start an electronic ignition fireplace?
Re-lighting pilot lights is straightforward on today’s modern gas fireplaces. If you have an electronic ignition unit, using your remote control simply press the ‘on’ button and the pilot will re-ignite within a few seconds, followed by the fireplace a few seconds after that.
How do I light the pilot light on my electronic ignition?
Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.
How do you start a gas fireplace with a lighter?
Flame-Lit Pilot Light Light a match or butane candle lighter and hold it near the burner in the fireplace. Turn the gas key to release gas to the burner. Pull the match or light away when the burner lights. You can adjust the flame height by turning the gas key.
Does my gas fireplace have a pilot light?
Most gas fireplaces have a standing pilot light, which is a small flame that burns even when you aren’t using your fireplace. If you don’t see the valve, it may be behind the fireplace, so look for it there and turn it on. Pull the fixed glass assembly off of the fireplace.
Do all gas fireplaces have pilot lights?
It is important to remember that not all gas fireplaces have “standing” pilot light, or, a pilot light that is “always on”. The best way to determine if you have this type of gas fireplace is to look at the control knob of the fireplace. On a fireplace you will normally find the control knob behind the grate or door.
Can you manually light a gas furnace with electronic ignition?
If your furnace is equipped with an electronic igniter, you cannot light the furnace manually. However, you may be able to get the furnace working by turning off the igniter and resetting it. Find the paperwork for your particular furnace to locate the reset button or switch.
How does electronic ignition work?
The electronic ignition system is the type of ignition system that uses electronic circuits, usually by transistors controlled by sensors to generate electric pulses which in turn generate the better spark that can even burn the lean mixture and provide better economy and lower emission.
Why is my gas fireplace not lighting?
If gas is coming out of the pilot, but it still won’t light, the spark igniter could be the problem. Alleyne says to look for and clear out any debris between the igniter and thermocouple. The pilot lighting, but not staying lit, indicates that the thermocouple is worn out, Worthen says.
Do electric fireplaces have pilot lights?
Electric fireplaces don’t have pilot lights. They create heat through internal electric heaters. You never have to worry about whether your pilot light is on or off.
Can I relight my own pilot light?
Your pilot light relies on your natural gas to stay aflame, so if your gas is shut off, your pilot light will go out. Simply turn your gas back on and either relight your pilot light yourself or call a professional.
How do you light a gas log without electricity?
Many gas fireplaces will work without electricity. You can run both intermittent pilot ignition fireplaces and standing pilot light systems during a power outage. IPI valve systems will normally have a backup battery system in place to ignite the flames.
Can you use gas fireplace if power is out?
Gas & wood fireplaces will continue to work safely during a power outage. These fireplaces do not require electricity for venting and can be used safely during a power outage.
How do I reset my electronic ignition furnace?
To reset the ignition control module on an electronic-ignition furnace, turn down the thermostat or turn off the power switch. Listen for the sound of the spark or watch for the hot surface ignitor to glow. Next, make sure the furnace’s flame sensor is clean.
How do you light a gas heater with electronic pilot?
If you have a gas furnace, here are the steps on how to light a pilot light. First, locate the pilot valve on the furnace. Find the gas valve and turn it to the “off” position. Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter.
Does an electronic ignition need a coil?
Electronic ignition does away with the need for a traditional condenser and points, so these need to be removed by unscrewing them from the distributor base-plate.
What are the disadvantages of electronic ignition systems?
The main disadvantage of electronic Ignition is that this system is very expensive because all cannot afford the vehicles having an electronic ignition system.
What is the difference between points and electronic ignition?
Conventional: While this is called a “conventional” ignition system, it’s something of a misnomer. These are not used on modern cars, at least not in the US. In an electronic system, you still have a distributor, but the points have been replaced with a pickup coil, and there’s an electronic ignition control module.
