Table of Contents
How do you light a Coleman propane furnace?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light.
How do you turn on a Coleman furnace?
Steps To Turn On A Coleman Furnace Check the air filter. It’s always a good idea to check the air filter before operating the furnace additionally or at the start of the season. Do a quick inspection. Flip the power switch. Adjust the pilot light as needed.
Where is the reset button on my Coleman furnace?
Turn the Coleman furnace system switch to the “Off” position on the electric service panel. Locate the manual reset switch near the left side of your furnace blower. Press the reset button, which you will find in the middle of the limit switch. Turn the system switch to the “On” position.
Where is reset button on gas furnace?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
Why won’t my pilot light stay lit on my furnace?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How do you light a pilot light?
If you have a gas furnace, here are the steps on how to light a pilot light. First, locate the pilot valve on the furnace. Find the gas valve and turn it to the “off” position. Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter.
How do I reset my Coleman thermostat?
To reset the thermostat model 9630-3361, put the thermostat in the off position , pull fuse wait 5 minutes , put the fuse back in wait another 5 minutes , then turn on.
What causes ignition failure on a Coleman furnace?
The flame couldn’t be established, check for a faulty gas valve, a dirty or defective flame sensor, a faulty hot surface ignitor, or a problem with the burner. There’s an ignition lockout due to repeated power recycles. Check if there is low gas pressure, a dirty or defective flame sensor, or a faulty gas valve.
Why is my furnace blowing cold air when the heat is on?
A clogged filter is one of the leading reasons for a heater blowing cold air. But even if you swap the air filter with a brand new one, dirt and debris can still be found within the unit. This could eventually lead to overheating. If your furnace looks pretty dirty, call an HVAC provider for a professional clean.
How do I reset the limit switch on a Coleman furnace?
How to Reset a Coleman Furnace Limit Switch Open the cover of your circuit breaker box. Examine the furnace to locate the upper limit switch. Depress and release the red “Reset” button in the middle of the upper limit switch. Return to the circuit breaker box.
What does 4 flashes mean on a Coleman furnace?
CODE: Four red flashes. RESULT: Limit switch is stuck while open. FIX: Check for a a dirty filter, an improperly sized duct system, an incorrect blower speed setting, or a faulty blower motor.
How do you light a furnace for yourself?
Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.
How do I ignite my furnace?
Furnace Look for a switch inside or near the furnace that turns it on and off. Make sure that it’s set to on. Make sure the gas valve is turned on. Examine the circuit breaker for the furnace. Check the pilot light. Leave the setting for lighting the pilot on for a few minutes after getting it lit.
Why is my gas heater not igniting?
One of the most common reasons for your gas heater not igniting or stopped working is because its thermostat is either off or not working properly. Therefore, make sure you check the thermostat, and if it is off, then turn it on while setting it on heat mode (5 degrees above your room temperature, at least).
Why is my furnace not blowing hot air?
First, check to make sure the thermostat is set correctly. You will want to make sure that the fan control is set to auto, and not ‘on’. If the thermostat appears set correctly, turn off your heater at the thermostat and check the filter. If the filter is dirty, replace it.
