Table of Contents
What size Jack do I need to level a mobile home?
The most important tools a mobile homeowner needs to check level is a water level and hydraulic bottle jacks. Two 10-30 ton hydraulic bottle jacks are also needed to re-level a mobile home. You’ll want to place the jacks at crossbeams, at the hitch, or the axles.
How much does it cost to jack up a mobile home?
To level a single-wide mobile home, expect to pay between $450 to $600, while leveling a double-wide mobile home can cost up to $900. Expect to pay $1,000+ for leveling wider mobile homes.
How can you tell if a mobile home is unlevel?
Signs your mobile home is unlevel Doors and/or windows that are difficult to open or shut. Unusual cracks in the walls, roof or floor. Awnings or attachments that are bent or difficult to use. Sounds of creaks and/or moans in the house. The skirting around your house looks like it’s buckled under pressure.
How do you level a floor in a mobile home?
How to Level Sagging Mobile Home Floors Dig holes for under where the floor is sagging if it is just in one or two spots. Use jacks which can be lowered into place in the holes, then lifted up to support the floor. Raise the jacks a couple inches each day if they need to go higher.
Will a 20 ton jack lift a mobile home?
Take a jack with enough load capacity to lift your mobile home. You need to know the weight of your home — including all the materials inside. In general, a jack with a 10 – 30 ton load capacity has enough potential to raise your home. Having two or more bottle jacks is better than one.
How many blocks go under a mobile home?
Set 8-by-8-by-16 inch concrete blocks on the slab to act as a pier under the mobile home. Double-stacking blocks is allowed in some communities if the stacks are no more than 5 blocks in height. Each row should be stacked at right angles to the abutting row of blocks.
What are mobile home Piers?
Footers and piers create the foundation that will support your mobile home once it is placed on a lot. Typically, the footers are made of concrete and the piers are cinder blocks that are stacked and fastened with mortar. The piers will be built to the height of the mobile home frame to provide support to the floors.
What causes soft floors in mobile homes?
Sagging mobile home floors: are usually a result of water damage in mobile homes with particle board flooring that doesn’t hold up well when it gets wet. Moisture Barriers Stop moisture from developing directly on the mobile home floor boards and will not allow the floors to rot.
Why is my mobile home sinking?
Excessive moisture in the soil under the mobile home causes the piers or blocks to sink. If the soil goes through periods of moisture and drying, the particles will expand and contract, which unsettles the home. The piers and blocks will sink or heave upward which shifts the mobile home’s floor.
What kind of plywood do you use for a mobile home floor?
The most recommended subfloor material is 5/8″ plywood. If you can afford water resistant marine plywood for your kitchen, laundry, and bath that would be a good idea.
What do mobile homes sit on?
A slab foundation under a manufactured home acts as a platform for support rather than the floor of the home. The slab typically sits on top of the ground with ground anchors embedded in the concrete. It is insulated around its perimeter, which keeps the ground beneath warmer.
What is a subfloor in a mobile home?
A subfloor is the base, bottom layer of wood flooring supporting carpet, tile and other types of flooring. Over the years manufacturers used different types of subfloors in mobile homes.
How do you jack up a mobile home?
How to Jack Up a Mobile Home: 4 Steps Step 1: Find out the problem area and go beneath the place. Step 2: Check the water levels on the I-pillars. Step 3: Place your mobile home jack to level the area. Step 4: Place large wedges or block to support the pillars to hold the level.
Where do you start when leveling a house?
When you know where the lowest portion of the center is located, mark that location. Build a temporary post using concrete blocks or large blocks of wood. Make sure that the post is located on firm, level ground under the house. Alternate the placement of each layer of blocks by 90 degrees to improve stability.
Can you reinforce a mobile home?
The primary downside to mobile homes is that they generally depreciate in value. Reinforce your mobile home’s support if it can’t be placed on a foundation. Install footings for the piers if the piers currently rest directly on the ground. Make sure your anchor or tie-down connections are firmly connected.
