Table of Contents
Can you put a hot tub on uneven pavers?
– The pavers should be solid and level for the hot tub So placing them on uneven surfaces for a long time would cause permanent damage to them. If the surface is not even, it will cause build-up in the tub. Ensure that when the tub is sitting on the paver, its base is in solid contact with the surface.
Can a spa sit on pavers?
Surfaces that suit hot tubs are: Concrete Slab – for spas you require a level base of 100mm (4”) minimum thickness with F72 mesh (subject to soil conditions). Pavers are OK as long as they are flat and are bedded well (concrete base or cement mixed with crusher dust).
Can you put a hot tub on paving stones?
Hot tubs require a level base that is able to support the weight of the hot tub when it is filled with water and bathers. You can use a concrete slab, gravel, a deck or patio pavers as options to support your hot tub.
How level does a hot tub pad need to be?
There should be a maximum of ½” (1.27cm) slope in an 8′ (2.44m) run. Do not use shims to level the spa, this could create tension on the spa shell which might result in damaging your spa. Because your spa pad must provide continuous support for the entire base of the spa, you should never level it with shims.
Can a hot tub be off level?
Leveling a hot tub that is on uneven concrete can be done with simple shims if the slope is less than one inch. For steeper slopes, leveling will require more involved solutions such as custom-built pads of wood, sand or gravel, or even a new concrete pad. We’ve written how to level hot tub on gravel before.
What is the best base to put a hot tub on?
A concrete surface is an excellent base for your hot tub as this material is extremely sturdy and long-lasting. If you have an existing patio made of concrete bricks, make sure it’s in good condition and is level (not angled for drainage). A customized poured concrete pad is an even better choice.
What do I put under my hot tub?
Gravel is an excellent choice for a hot tub base. It’s relatively cost-effective and easy to install, plus it’s very good for drainage. This is important because you need to make sure any rain water or overspill from your hot tub is able to drain away from the base. And unlike concrete, gravel won’t crack over time.
How much weight can pavers support?
Pavers can withstand at least 8,000 pounds of pressure per square inch before material failure.
Can you put a spa on tiles?
We understand that your Swimming pools or Spas are the ultimate wet places that require proper tiling and the beauty of your pool totally depends on the type of tiles used. For use in the pool and spa we have the ceramic and porcelain tiles that are quite popular and have been used for decades.
Can you put a hot tub on paving slabs?
Most patios, block paving and other surfaces are already reinforced and will be able to take the weight of a hot tub placement. It is worth ensuring the stones are level and also worth ensuring the drainage is ok as you do not want water to pool under the hot tub.
Does a hot tub have to sit on concrete?
Outdoor hot tub placement, such as decks, concrete or brick patios, is common. However, the hot tub can be placed on any solid, uniform, level surface. Do not place your hot tub on grass or bare ground.
How much slope should a hot tub pad have?
The spa pad should be at least the size of the spa. If you are going to pour cement pad put a slight slope in it so that water won’t pool under the spa. A 3/4″ slope in a 10 foot wide cement pad is adequate. If you use bricks or patio blocks, they should set on at least a 3″ base of sand, pea gravel or crushed stone.
How do I level my backyard for a hot tub?
Place a layer of gravel on the leveled spot. The thickness of the layer will depend on the size and weight of your hot tub, but a layer four to six inches thick should be adequate for most hot tubs. Extend the gravel out around the tub in all directions, to avoid having a muddy area around your hot tub.
How do you level a hot tub with gravel?
Gravel should be completely flat and level before placing the hot tub to avoid damage. Take extra care to level it with your shovel and ensure there are no high spots.
What is a spa leveler?
The Spa Level-R™ is a solid, secure base used to level your hot tub. It elevates your hot tub off the ground to encourage proper water run-off which will: Protect the hot tub base from wood rot damage. Eliminate green mildew stains on your concrete.
How much slope can a hot tub have?
A dip in the ground can cause your hot tub to crack. When installing a hot tub, understand that a slight slope of ½-inch per every 8-inches of hot tub length or width is expected to help with tub drainage. Therefore when leveling, your main concern is to ensure the surface is flat.
