Table of Contents
How far apart should the posts be on a deck?
In general, posts should be spaced no more than 8 feet apart. Some builders position them every 4 feet for a completely rigid frame. The maximum distance between footings is determined by the size of your joist material.
Should I use 4×4 or 6×6 deck posts?
Unfortunately, a 4×4 post may not be able to withstand the weight, causing the entire porch to buckle. A 6×6 post gives you a little more long-term stability, particularly in those colder climates. Not only does it perform better when carrying heavier loads, but it also makes the heading for your roof more secure.
How many footings do I need for a 12×16 deck?
A standard deck will need four footings parallel to the house, but they will need to be temporarily braced by 6 inch-by-6 inch posts. Using doubled boards, you will then need to build beams on the top row of the posts to frame the edges of the deck. These must be topped with adjustable post caps.
Should deck joists be 2×6 or 2×8?
In general terms, joists spaced 16 inches on center can span 1.5 times in feet their depth in inches. A 2×8 up to 12 feet; 2×10 to 15 feet and 2×12 to 18 feet. The larger the deck, the larger the joists. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards.
How do you stagger deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
Do joists go on top of beams?
One of the most traditional ways to frame without joist hangers is to have the joists rest on top of a beam. There’s nothing wrong with this method, but realize the top of the beam will be at the bottom plane of the floor joists. It’s easy to install the hanger so tight you can’t get the joist into the hanger.
Should you notch deck posts?
Say “No” to notching pressure-treated deck posts. We want you to build an outdoor railing system that you, your family and guests can enjoy without worrying about safety issues. In order to do so, you need to know this building shortcut is not advisable, and we recommend avoiding it at all costs.
What accounts for roughly 90% of all deck collapses?
About 90% of deck collapses occurred as a result of the separation of the deck ledger board from the house, allowing the deck to swing away from the house. It is very rare for deck floor joists to break mid-span. Many more injuries are the result of rail failure, rather than complete deck collapse.
How far apart should 6×6 deck posts be?
For Building a Deck Railing, Deck Frame, or Fence The maximum spacing of 4×4 deck posts should be 6 feet on center, while the maximum spacing of 6×6 deck posts should be 8 feet on center.
Should deck posts be set in concrete?
A deck post should always be placed on top of footing, not inside concrete because it can break. Concrete tends to absorb moisture and wood expands when it gets wet, so these two factors combined will result in the wood breaking the concrete.
How many deck blocks do I need for a 12×12 deck?
Calculating Out How Many Deck Blocks for a Floating Deck Deck Dimension Square Feet of Deck Number of Deck Blocks 12″ x12″ Supporting 2000 lbs 8×8 64 4 8×10 80 4 10×10 100 4 10×12 120 6.
How thick should joists be on a deck?
CHOOSING THE RIGHT DECKING BOARD THICKNESS Decking Type Actual Thickness (inches) Suggested On Center Joist Spacing (inches) Tropical Hardwoods 1x 13/16” 16” Thermally-Modified 5/4 1” 16” Pressure Treated Pine 5/4 1” 16” Western Red Cedar 5/4 1” 16”.
Should I use deck boards or 2×6?
2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions. The primary function is to drain water from the deck. Gaps that are narrow (1/8”), can catch debris, specifically on top of the joists, and can be difficult to clean out.
What size wood should I use to build a deck?
For the deck surface, you can use 2x4s, 2x6s, or 5/4x6s. The 5/4 decking (pronounced “five-quarter”), available in cedar and pressure-treated fir, is 1 inch thick and 5-1/2 inches wide with rounded edges that make for a splinter-free surface. Cedar 1x lumber usually has one rough side and one smooth side.
Is it OK to stagger deck boards?
Staggering the deck boards decreases the number of screws or nails going into one joist, which can weaken or rot the joist more quickly. Staggering the joints strengthens the deck by spreading the seams across more joists instead of placing the stress on only one.
Do deck boards need to end on joist?
All deck board should end on a joist, making sure to stagger deck board ends. While laying deck boards might seem easy and quick, you’ll want to take your time and do it right. One small mistake could result in you having to remove all the deck boards later to fix that extra-wide gap or crooked deck board.
Can you use screws for joist hangers?
Outdoors use 16d double-dipped galvanized nails (or stainless steel when called for) for installing hangers. The manufacturers agree: Never use galvanized deck screws or drywall screws to install joist hangers. Those screws don’t have the shank size and toughness to support joist loads.
Is it better to use joist hangers?
Joist hangers are better because they allow for more accurate placement of joists. They also allow for toe-nailing, plus support the underside of the joist. This makes the hanger stronger than a toe-nail. While joist hangers are an expense, the ease and increased strength make them a better choice.
