Table of Contents
Step-by-step Clamp a guide to the square. Find the crown. Lay out the first tread and the second riser. Lay out the second tread and the third riser. Mark the back of the top tread. Mark the plumb cut at the top of the stringer. Lay out the bottom riser. Adjust the first riser height.
How do you calculate stair stringers?
How do I calculate a stair stringer? Start by finding the overall height that the staircase will be. Decide the height or “rise” you’ll want for each step. Divide the total height of the staircase by the height or “rise” you want for each step.
How do I make sure my stair stringers are square?
Square Check the perpendicular alignment of each stringer at the edge of the deck with a framing square. Hold the short leg of the square against the edge of the deck and the longer leg against the outside of a stringer. Tap the side of a stringer at the bottom where the first tread will attach using a hammer.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How long should a 2×12 staircase be?
How to Use the EZ Stair Calculator. We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths.
How far apart do stair stringers need to be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
How many stairs do you need to go up 8 feet?
Stair Rise for 8-Foot Ceilings An 8-foot ceiling will need 14 treads. Divide 96-inches (8-feet) by 7-inches to get 13.71 treads, and round up to 14. In this case, you would not round down as you would have one step that is too tall.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
What are the dimensions of a stair stringer?
So, in general, the typical stairway is 36 inches wide. The number of stringers installed at a wood-framed stairway is related to the 36-inch minimum width. If cut stringers are used in the stair construction, then at least three stringers are required. Cut stringers should be spaced no more than 18 inches on center.
Can you use shims on stair stringers?
If you’ve cut your stringers and realize you’ve cut too much off and now the steps will have a ¼ inch or more difference, you will need to use shims to fix it. If the angle you’ve cut on the stringer gives the step the right pitch, you can use two (or more) shims to bring the whole step up to the right height.
Can you make a stringer out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
What size lumber are stair stringers cut from?
Selecting stringer stock Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.
What size lumber do you use for stair risers?
Stair stringers are cut from 2×12 lumber. For exposed side stringers, use cedar lumber. Make one stringer for each 16 inches of stair width. Allow for light boxes if riser lights will be installed.
What is the rise and run of deck stairs?
A stair rise is the vertical distance from the top of one tread to the top of the next tread. The total run is the overall horizontal distance traveled by the stringer. The total rise is a stairway’s overall change in height, from the landing pad to the top of the deck’s decking.
What angle should stair stringers be?
Stair codes and guidelines prefer an angle of around 37° for normal stairways (the green area in our illustration) and around 7° for ramps (the yellow area in our illustration).
Can you use joist hangers for stair stringers?
Use joist hangers to fasten the blocking. Pros: Allows for the use of all types of stair stringer hangers. The top of the stair stringer acts as the first tread instead of being flush with the deck’s surface.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
Does the landing count as a step?
Does the landing count as a step? Yes it does. It amazes me how many people like to argue this one. Remember that when counting stairs, you are counting how many times you have to lift your foot.
How long do stairs need to be to go up 10 feet?
For most homes, the length of a flight of stairs is between 9 and 12 feet long. The total length of a flight of stairs for an 8-foot ceiling is approximately 9-feet long. The total length of a flight of stairs for a 10-foot ceiling is approximately 12-feet long.
How many steps does it take to go up 9 feet?
What is the Height for a 9-Foot Interior Wall Home? If you have nine-foot-high walls on the first floor, your total height is 120 and 5/8 inches. Once again this is not equally divisible by 7.5, but it yields 16 risers. Multiply the 15 needed treads by 10 inches and you get 150 inches or 12 feet 6 inches.
