Table of Contents
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
What are the signs of a bad ballast?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
How do you test a ballast?
To measure it, set your digital multimeter to around a thousand ohms resistance setting. Connect the black leads to the white ground wire on your ballast. Afterward, test every other wire with the red lead. When you do this test, a good ballast will return an “open-loop” or max resistance.
How do you tell if it’s the ballast or the bulb?
One probe of the multimeter should touch the hot wire connections, while the other touches the neutral wire connections. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.
How do you tell if a fluorescent ballast is bad?
If the ballast is bad, the needle on the multimeter will not move. If the ballast is still good, the needle should sweep to the right across the face of the multimeter. Install a new ballast, if necessary. Replace the ballast cover on the fluorescent light fixture.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
How long do ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Why do my fluorescent lights not turn on?
The fluorescent tube won’t turn on No electrical power due to a tripped breaker or blown fuse. A dead or dying ballast. A dead starter. A dead bulb.
Why is my fluorescent light not working?
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely!.
How much does a ballast cost?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
Why is my new fluorescent light flickering?
Lamp blinks: This is usually because of a poor connection where the tube fits into its sockets at each end. Take the tube out and clean the pins at each end with fine steel wool. Brush dust out of sockets, then reseat firmly.
Can a fluorescent light work without a ballast?
Reverted question “ Can I make a fluorescent light work without a ballast?” yes, you can, but you need something to reduce the current as the bulb warms up. So, you can drive a fluorescent with a pulse width adjustable power supply, but this is what is in an ‘electronic’ ballast.
Is ballast needed for LED tube?
No LED bulbs require a ballast, although some are engineered to work with an existing ballast. You will find ballast-compatible or “plug-and-play” LEDs that are designed to replace linear fluorescents, compact fluorescents, or HIDs. Incandescent and halogen lamps do not require a ballast.
Will LED lights work with bad ballast?
Can LED lamps work off of existing ballasts? Yes, if they have an internal driver than can work off that ballast. Philips, for example, has designed a tube that is compatible with an existing electronic ballast.
Can you repair a ballast?
While simply swapping burned out bulbs in an existing ballast is deemed “ballast repair” by many – and can offer advantages in longevity and energy savings – sometimes this simple “fix” is not enough.
How often does a ballast need to be replaced?
The ballast takes in electricity and then regulates current to the bulbs. A typical ballast will generally last about 20 years, but cold environments and bad bulbs can decrease this lifespan significantly. You can get a new ballast at a hardware store or home center and install it in about 10 minutes.
