Table of Contents
Where should the expansion tank be installed?
An expansion tank is generally installed directly above the water heater by means of a tee-fitting installed in the cold water delivery pipe. The expansion tank is usually installed vertically, though it is acceptable to install it horizontally if it is necessary because of space limitations.
How do you install an expansion tank on a water heater?
How to Install Water Heater Expansion Tank Step 1: Disconnect the Water and Power Supply. Step 2: Bring Out Expansion Tank and Accessories. Step 3: Confirm the Water Supply Line for Cold Water. Step 4: Install the Expansion Tank. Step 5: Attach the Heater Tank. Step 6: Restore the Water and Power Supply to the Heater.
Does it matter which way an expansion tank is installed?
Expansion tanks can be installed in any direction. Whether oriented uprightly, horizontally, or even upside down, the expansion tank will function properly without any adverse effects. When putting an expansion in an abnormal position (specifically sideways or horizontally), make sure to support the tank.
Does expansion tank need to be above water heater?
Your expansion tank can be anywhere on your plumbing system and does not need to be installed in close proximity to the water heater. It is most commonly installed using a “T” at the cold inlet to the water heater. But, functionally, it can be installed anywhere on the cold inlet line.
How close should an expansion tank be to a water heater?
The items which should be installed in sequence in the cold water line are (1) the EXPANSION TANK must be installed at least 18 inches away from the cold water inlet fitting on the water heater, (2) the PRESSURE GAUGE, and (3) the PRESSURE REDUCING VALVE, if required, see Figure 1.
What pressure should my expansion tank be set at?
The recommended water pressure is between 50 and 60 PSI. Thermal Expansion Tanks contain an air bladder which is pressurized with air, and expands and contracts to absorb the expanded water from the water heater. needed. Check the air pressure in the Expansion Tank using a tire gauge.
What size expansion tank do I need for a 40 gallon water heater?
General Guidelines for Sizing an Expansion Tank Water Heater Capacity Supply Pressure (psi) Expansion Tank Size 40 to 60-gallon 40-50 psi 2-gallon 40 to 60-gallon 60-80 psi 3.2-gallon 80-gallon 40 psi 2-gallon 80-gallon 50-60 psi 3.2-gallon.
Can an expansion tank be installed horizontally?
Can a water heater thermal expansion tank be installed sideways/horizontally? Most expansion tanks are designed to be installed vertically (stem up or stem down). You can install one sideways, but it will shorten the lifespan unless it is designed and specified by the manufacturer for horizontal installation.
Why is the expansion tank on the cold side?
One expansion tank manufacturer states: “We recommend the cold water side installation because the tank is not insulated. When the expanded volume enters the tank, it will cool down. With the tank on the cold water side, this expanded volume will pass through the water heater before going out to the faucets.”Feb 28, 2010.
Should an expansion tank be vertical or horizontal?
Do mount tank vertically with connection at top: It is also best to install diaphragm type expansion tanks vertically with the piping connection at the top. This reduces stress on the tank’s connection relative to horizontal mounting.
Should expansion tank be supported?
All expansion tanks (even the small 2-gallon tanks) should be supported in some way. You want to match the pressure in the expansion tank as close as possible to the water pressure of the house.
Can I install expansion tank with PEX?
Connect Tank to Tee Cut a piece of PEX to run between the expansion tank and the tee-fitting that you inserted in the hot water tank cold water supply line. If you have other fittings between the two, you will need to cut pieces of PEX to connect those as well.
How much does it cost to add an expansion tank to a water heater?
$145 – $350, Installed The cost to install a water heater expansion tank ranges from $55 and up for the rare DIY project, to about $350 when a pro adds an expansion tank to a large residential water heater.
What happens if expansion tank pressure is too low?
If the precharge pressure is too low the tank may be excessivly full of water even before the thermal expansion takes place which may limit room for expansion, add additional weight to the tank, and, or, stress the tank bladder. These factors may reduce its service life.
Will an expansion tank increase water pressure?
The expansion tank contains air, which is highly compressible. Expanding water from the water heater can flow into the expansion tank, where the air compresses, making room for the increased volume of water. Water pressure in the system doesn’t increase significantly.
What size expansion tank do I need?
As a general rule, the bigger the water heater, the bigger the expansion tank. For a 50-gallon water heater, you require a 2-gallon expansion tank. Depending on how high your water pressure is, however, you may need to go up a size to a 4.5-gallon expansion tank.
How do I know if my expansion tank is working?
The tank should be full of air and therefore sound hollow. If it makes a dull thud rather than a hollow sound, your tank is full of water and needs repair or replacement. You can also gauge this by feeling the tank, which will be cool where it’s holding air and warm where it’s holding water.
Should expansion tank have water in it?
That’s where the expansion tank comes in. Properly installed, it absorbs this excess pressure. Half of the tank is filled with water from the main water system of your home. As the water in your water heater gets hotter and expands, it pushes against that bladder and further compresses the air on the other side.
