Table of Contents
How do you install a wall thimble?
How do you install a wood stove pipe through a wall?
How do you seal a thimble on a wall?
Select one half of the Wall Thimble for the outside of the wall. 1. Apply a continuous bead of high quality silicone or silicone/latex caulk on the inside of the outer flange. This is the only weather seal to keep moisture outside the building; take care at this step.
How do you wire a chimney thimble?
Chimney Plugs The black outside plate covers up to a 10″ diameter hole. Installs easily, simply insert the plug into the old thimble opening and tighten the expansion screw on the face of the plug. The side expand and create a tight fit inside the thimble opening. To remove simply reverse the process.
Is a wall thimble required?
Running any residential or building heating appliance, burning gas, liquid, or solid fuels through a combustible wall, will require an Insulated Wall Thimble as your passageway to connect appliances to interior or exterior masonry chimneys.
How close can you put a wood stove to a wall?
The standard clearance recommended by the National Fire Protection Agency is 36 inches. This means that the back of the stove should be 36 inches away from any combustible material, such as woodwork, unprotected walls, furniture and even firewood.
Does a wood stove pipe have to go straight up?
The pipe should be as straight and short as possible, with sections properly secured. If it must have angles, limit them to one or, at the most, two sweeping 90-degree elbows or the equivalent. The horizontal portion of the pipe should rise not less than one-quarter inch to the linear foot, to insure a good draft.
What do you put on wall behind wood stove?
The fireback is a traditional heat shield for a stove The solution of replacing the back wall with a heat-resistant material, such as heat-resistant stones or a wood stove heat shield, is often cumbersome and not always beautiful.
How do you seal a thimble?
Lay a bead of cement, onto the end of the Thimble that butts against the masonry chimney. (See Figure 7) The cement will act as an adhesive and also seal the Thimble tightly to the masonry chimney should there be uneven surface. If the masonry chimney has a smooth surface the Cement will not be required.
How do you seal a flue pipe on a wood-burning stove?
Sealing. Use stove pipe cement or caulking material rated for use with a wood stove. The cement must be able to withstand high temperatures. Clean the area with a wire brush prior to sealing to remove any rust or debris.
How does a wood stove wall thimble work?
The thimble enters the flue inside the chimney and is designed to accommodate a stovepipe. If the homeowner no longer uses the wood-burning stove, the pipe is removed, and the thimble port is covered over by drywall, wallpaper, or a pie-plate cover.
How much is a fireplace insert?
How much does a fireplace insert cost? Most fireplace inserts and a professional installation cost about $2,000 to $4,000, depending on the state of your existing chimney and the model you select. Some electric models cost significantly less, but they offer less heat output than wood and gas fireplace inserts.
What is a fireplace thimble?
The thimble is the round opening that can be found in a brick or stone chimney about five feet above floor level. The thimble enters the flue inside the chimney at a 90 degree angle and is designed to accommodate the entry of a stovepipe from a wood stove.
How do you install a clay thimble?
Apply a layer of stove cement to the edges of the opening, using a trowel. Install the thimble by simply sliding it in place so it extends to the inner edge of the chimney liner, but not past it. Apply additional stove cement to fill any gaps and to seal the thimble securely. Let dry.
How hot does a wall thimble get?
Maximum Continuous: 1,000 Degrees Fahrenheit / 540 Degrees Celsius.
What is a vent thimble?
The DuraVent Direct Vent Pro Wall Thimble is used for horizontal venting to provide a safe passageway through the side of the home. The Wall Thimble is able to adjust to varying wall thicknesses. The cover comes with an insulated ring to reduce any infiltration through the wall.
Can you side vent a wood stove?
Although putting a wood stove on an interior wall works best for a number of reasons, you can vent the stove to an outside wall if the interior option is not possible.
How do you fireproof a wall behind a wood stove?
Common fireproof wall ideas for behind a stove include stone, brick and tiles. The look of a wood burning stove can be enhanced by using a faux panel (such as a stone veneer look) or using a fireback.
How close to wall can wood stove be with heat shield?
The Fire Protection Association recommends that the common radiant-type stove must be spaced out by 900mm (36 inches) from a combustible wall. Using a heat shield can reduce the space required to 95mm as stated by HETAS.
What is considered a non combustible wall?
Non-combustible materials are building materials that do not burn or ignite when subjected to expected levels of fire or heat. Examples of non-combustible materials include brick masonry, concrete blocks, hardy backer board, calcium silicate board, cement board, metal, and certain types of glass.
