Table of Contents
Do you nail the tongue or groove?
For tongue-and-groove flooring, drive a nail at a 45-degree angle through the tongue, then conceal it by engaging the groove of the next board. Be sure to countersink the nail — drive it slightly below the surface of the wood — to prevent interference in the joint.
When installing laminate flooring where do you start?
Always start hardwood flooring along the most prominent and noticeable wall in the room. This way, if the room is out of square, the crooked cut will be hidden under the cabinet’s toe kick. In order to keep the floor straight and square, start laying the laminate away from the wall because the wall may not be straight.
Which is tongue and which is groove for laminate flooring?
Each laminate flooring plank contains a tongue and groove, these edges of the board cause your locking system to click together. The tongue on laminate flooring is the small flat edge on one side of the board, this is the top edge that is going to angle and lock into the bottom side of another board.
Do you cut the tongue off the first row of laminate?
Place the first plank with the tongue side towards the wall, being sure to allow 1/8″ for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap. If it is too short, cut a new plank in half and use one half to start the second row.
Should tongue and groove be glued?
The recommended glue for floating installation is Tongue and Groove engineered flooring glue. Glue placement is very important. The glue must be placed along the topside of the groove the full length of the grooved side and end.
How do you stop laminate flooring at doorways?
How To End Flooring at a Doorway Lift to Fit. Plan on a seam in the middle of the doorway. Notch and cut the first piece to fit and then slide it completely under the jamb. Slide Both Pieces Over. Once the two pieces are connected, slide them both over just far enough so that both jambs cover the flooring ends. 11 / 12.
How soon can you walk on laminate flooring?
wait for the floor to cure Before you use your new floor or move into the room, make sure the floor is completely cured. Do not walk on the floor for 24 hours after installation. If you do, it will damage the installation, resulting in an uneven floor.
How do you start the first row of laminate flooring?
Begin the first row of flooring by placing the planks with the tongue side facing the wall. Install the second plank next to the first by aligning the tongue into the groove and press the plank down to snap it in place. When you come to the end of the first row, cut the length of plank needed to complete the row.
How do you put up tongue and groove?
Hang each board of the first and every successive row, always ensuring the board is the proper length or height before attaching. Butt edges together in the same row, and slide the groove of the next board over the previous tongue for each following row. Nail only the tongue side for each row after the first.
Do you stagger laminate flooring?
Laminate flooring manufacturers often require their floors to be staggered anywhere between 6 to 12 inches, some manufacturers even want more. Don’t ever short-stagger your flooring, it is both not aesthetically pleasing, and can also bring up some of the same issues as not staggering the floor at all.
Which way should you lay laminate flooring in Long room?
In general, laminate manufacturers recommend laying laminate flooring perpendicular to the longest wall in a long, narrow room to avoid a bowling alley effect. When the boards are laid across the room, the lines between the boards and the wood pattern visually widen the room.
Can you lay laminate flooring right to left?
We recommend starting in the left corner of the longest wall in the room and to install the planks in the same direction as the main light source (e.g. the main window). Planks are always installed from left to right.
Do you lay laminate flooring vertically or horizontally?
You can lay your flooring either horizontally or vertically. Vertically will elongate a room and works great if pointing towards a window, as it will follow the natural light. Laying laminate flooring horizontally will can make a small room appear larger.
How tight should tongue and groove be?
All it takes is 1⁄8″. The joint should be a firm press fit: If you have to knock the pieces together, then struggle to pull them apart, the joint’s too tight. A tongue that’s a hair too fat for the groove may actually seat, but it will stress the groove sidewalls and may, in time, prompt them to split.
Which side of laminate flooring goes against the wall?
The tongue is the side that you will want to place against the wall as you start your laminate-flooring installation.
How much glue do I need for tongue and groove flooring?
To calculate the amount of adhesive to purchase, simply multiply the values supplied by the number of square feet of flooring you are going to install. For example: 6” planks require 240 lineal feet of adhesive per 100 square feet of flooring to be installed. If your job is 500 square feet, multiply 5 x 240 ln.
Do you need transition strips between rooms?
Why Do I Need to Use Transition Strips? Transition strips serve two main purposes in a residential or commercial space. First, they’re put in place to make navigating from room to room easier. They also provide a visual break between rooms and flooring materials that might otherwise be jarring and less than attractive.
Does laminate flooring need transitions?
If you decided to install either hardwood, ceramic or laminate, you will need the transitions. These transitions are useful for two main reasons. Firstly, they ease the navigation from one room to another. They also visually divide rooms and different floorings.
Where should flooring meet in a doorway?
So, you’ll want to make sure that your transition from one floor to another is set right in the middle between the door. All you’ll do is simply change the boards in the middle of the doorway and continue your installation with the other flooring in the other room.
