Table of Contents
Do you need plywood under T1-11 siding?
It is best to check the local building code to determine if plywood sheathing is required. Even though it may not be considered necessary, many builders feel it is best to use plywood under T1 siding if the structure will be used for human habitation.
What goes under T1-11 siding?
You should put sheeting and house wrap under the T1-11 siding, just like with any other siding. In some areas, you don’t have to use sheeting and house wrap to do the installation, but I would not recommend doing it that way.
How do I fasten my T1-11?
T1-11 siding is designed for installation on framing with standard 16-inch spacing. You can attach them with exterior screws or galvanized nails. Wrap the house with house wrap or 15 mil tarpaper. Staple the material to the studs with a staple gun and cut openings for doors and windows with a utility knife.
How do you seal the bottom of T1-11 siding?
Trim the siding with one-by-four-inch wooden trim, covering the gaps around windows and doors, under the soffit and on the corners of the house. Nail the trim with two-inch galvanized nails, then caulk around it with acrylic latex caulk.
Can T1-11 be hung horizontally?
1 Answer. If you carefully read the instructions, you will not find any instructions that say it cannot be installed with the grooves horizontal. Rather, they only show it installed vertically.
Can I use screws for wood siding?
Although ring-shank siding nails are suitable for wood siding installation, screws have better holding power over time. Stainless steel is strongly recommended for all woods and required for modified woods such as Accoya and Kebony.
Should you seal the bottom of siding?
DO NOT seal the bottom with any sort of impermeable caulking nor spray foam. The bottom should remain permeable so that if water gets behind your siding for whatever reason then it has an escape path.
How much is a sheet of T1-11?
T1-11 Plywood Costs Depending on the finish and size, this siding costs between $25 and $40 per 4 foot by 8 foot sheet. Add installation costs and construction materials, and you end up with a range between $3.50 and $7.20 per square foot.
How do I fasten plywood siding?
Fasten the panel with galvanized finishing nails and a hammer. Drive nails about 6 inches apart on the panel edges, about 12 inches vertically in every stud. Work from the corner in to keep the panel side straight — don’t nail both edges and then try to nail the center.
Is T1-11 siding waterproof?
T1-11 siding is not waterproof because it is not treated with any resins and chemicals that repel moisture. T1-11 siding needs to be protected against the weather with primer, paint, or stain. You also need to caulk around doors, windows, joints, and nails to keep the water out.
What is better than T1-11?
It can stand up to harsh weather in any climate and resists damage from termites and fungal decay. How to Decide: If you want the most durable siding available, then LP wood siding is your better choice. If you want to sacrifice some durability for savings, then choose the plywood grade over the OSB T1-11.
Can I use screws for SmartSide panels?
LP SmartSide has three product categories: Precision Series, Foundations and Architectural Collection. When installing Precision Series lap in this application, you may use 0.091″ diameter, hot-dipped galvanized ring shank nails or #8 hot-dipped galvanized tapered head wood screws. You must use nails.
What nails do I use for siding?
Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig.
Do you caulk between T1-11 siding?
The top T-111 panel should be installed about 1/4 inch off the shelf formed by the flashing to prevent moisture from wicking up into the wood. This is especially important when using engineered siding. If the siding was installed with Z-flashing, do not caulk in the grooves.
Is it better to paint or stain T1-11 siding?
Plywood T1-11 accepts stain well and takes on a grainy appearance that blends well in rural surroundings. Staining T1-11 is less work than painting it — you may need only one coat — but prior cleaning of the substrate is even more important, because any dirt and discoloration shows through.
What does T1-11 stand for?
What does T1-11 Stand For? The siding stands for Texture “tee-one-eleven”. It refers to the textured grooves or channels that are cut into one face of the siding. The siding is available in two major grades: plywood and OSB.
Can siding panels be installed horizontally?
Horizontal Siding Installation: Pros and Cons For starters, it’s the least expensive option, making it ideal for homeowners needing siding replacement on a budget. For starters, horizontal siding can be less durable than vertical siding. That’s because it’s more prone to water damage over time.
Can SmartSide panels be installed horizontally?
LP SmartSide siding is designed for horizontal installation only. Un- grooved LP SmartSide Precision series panel siding is available for board and batten applications. Refer to the installation instructions for proper installation.
Is it better to nail or screw siding?
Nails are often preferred for structural joining, including framing walls, because they are more flexible under pressure, whereas screws can snap. Nails are also called upon when securing plywood sheathing for exterior walls, installing hardwood floors, and attaching siding and roofing.
