Table of Contents
How do I install T1-11 siding myself?
What goes under T1-11 siding?
You should put sheeting and house wrap under the T1-11 siding, just like with any other siding. In some areas, you don’t have to use sheeting and house wrap to do the installation, but I would not recommend doing it that way.
Do you nail T1-11 in the grooves?
T1-11’s grooves and shiplap edges run parallel to its 8-foot-long edge. The T1-11 siding’s 1-inch-wide, 1/4-inch-deep grooves are spaced 11 inches apart. Contractors nail T1-11 siding to a building’s exterior and usually protect its surface with paint.
How do I fasten my T1-11?
T1-11 siding is designed for installation on framing with standard 16-inch spacing. You can attach them with exterior screws or galvanized nails. Wrap the house with house wrap or 15 mil tarpaper. Staple the material to the studs with a staple gun and cut openings for doors and windows with a utility knife.
Do you need plywood under T1-11 siding?
It is best to check the local building code to determine if plywood sheathing is required. Even though it may not be considered necessary, many builders feel it is best to use plywood under T1 siding if the structure will be used for human habitation.
How do you seal the bottom of T1-11 siding?
Trim the siding with one-by-four-inch wooden trim, covering the gaps around windows and doors, under the soffit and on the corners of the house. Nail the trim with two-inch galvanized nails, then caulk around it with acrylic latex caulk.
Can I use screws for wood siding?
Although ring-shank siding nails are suitable for wood siding installation, screws have better holding power over time. Stainless steel is strongly recommended for all woods and required for modified woods such as Accoya and Kebony.
Should you seal the bottom of siding?
DO NOT seal the bottom with any sort of impermeable caulking nor spray foam. The bottom should remain permeable so that if water gets behind your siding for whatever reason then it has an escape path.
Is T1-11 siding waterproof?
T1-11 siding is not waterproof because it is not treated with any resins and chemicals that repel moisture. T1-11 siding needs to be protected against the weather with primer, paint, or stain. You also need to caulk around doors, windows, joints, and nails to keep the water out.
Do you need sheathing under plywood siding?
It is completely okay if you were not aware that there’s no sheathing under siding until you removed it. Sheathing works as a case or cover, structural support, insulator, and more. Missing sheathing is not any structural defect. It’s possible that it was not added to the construction plan.
How much does it cost to install T1-11 siding?
The average cost to install T1-11 plywood siding ranges between $1,500 and $3,700, with an average of $2,500 for 500 square feet of exterior wall space. For OSB siding, that cost stays in the same general range, but the average drops down to $2,200 for the same 500 square feet.
Can I use screws for siding?
Fastener Choices Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig. 15).
Can I use screws for SmartSide panels?
LP SmartSide has three product categories: Precision Series, Foundations and Architectural Collection. When installing Precision Series lap in this application, you may use 0.091″ diameter, hot-dipped galvanized ring shank nails or #8 hot-dipped galvanized tapered head wood screws. You must use nails.
How do I fasten plywood siding?
Fasten the panel with galvanized finishing nails and a hammer. Drive nails about 6 inches apart on the panel edges, about 12 inches vertically in every stud. Work from the corner in to keep the panel side straight — don’t nail both edges and then try to nail the center.
Is it better to paint or stain T1-11 siding?
Plywood T1-11 accepts stain well and takes on a grainy appearance that blends well in rural surroundings. Staining T1-11 is less work than painting it — you may need only one coat — but prior cleaning of the substrate is even more important, because any dirt and discoloration shows through.
Can you use T1-11 without sheathing?
In some construction techniques the use of T1-11 can act as both a wall cladding and sheathing all in one. These panels need to be rated for structural use. This means if you removed the sheetrock and insulation you would see the house wrap. Not any sheathing.
Is T1-11 pressure treated?
T1-11 siding features narrow, evenly spaced grooves on a rough-finished board for a pastoral appearance. Pressure treated for above ground applications, T1-11 siding features grooves spaced either 4″ or 8″ on-center to provide options for achieving the look you desire for your home, shed or pump house.
