Table of Contents
How do you install premade deck stringers?
Do stringers need hangers?
To attach stair stringers to a deck, you must use a metal stair stringer hanger. End-nailing, toe-nailing, or screwing stringers to a header is not allowed per the International Residential Code. Metal hangers must use appropriately sized nails or fasteners specific to the stringer hanger manufacturer.
Do you install risers or treads first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser.
How do I support a stair stringer?
If your stringers are more than 10′ long, we recommend installing a rigid beam at mid-span to add support to the structure. The strength of stair stringers is considerably weakened by the cuts made to create the stair surfaces, and stairs must be.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How far apart should deck stringers be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
How much space should be between stringers?
Stringers should be spaced no more than 36 inches apart from each other for maximum stair support, according to the International Association of Certified Home Inspectors. However, local residential codes may vary slightly, so check the building codes before building a staircase.
How many steps are in a 4 foot deck?
A four-foot high deck can have a range between 6 and 8 steps.
How do I fasten deck stringers?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
Can you use joist hangers for stringers?
This metal bracket supports the stringer and holds it on the framing. Stringer hangers look like joist hangers and function in the same way. Most local code authorities require the use of stringer hangers, and using them makes installation easier.
How far should a tread overhang the riser?
Stairs must have an overhang between 3/4″ to 1-1/4” to increase the depth of the step, making it better for descent while maintaining a clear 10-inch going for the ascent. Treads that are 11-inches deep or greater do not require an overhang.
Do you glue risers?
Don’t fasten treads and or risers with only nails or staples. The adhesive is much more important than the fasteners. There will be times when fastening may be limited, so a good adhesive is critical. Don’t use the stringer as a level for the treads.
Should you stain stair treads before installation?
Staining and varnishing hardwood treads prior to installation is recommended, especially in this case where we have stone or tile risers. Once the treads are stained and dried it’s time to cut and install them.
How long can stringers be without support?
The minimum recommended size for a deck stair stringer is 2×12, which has a maximum recommended unsupported span of 6 feet. Often this maximum span is dangerously exceeded, resulting in overspanned stringers that will deflect and cause the connection at the deck to pull loose and fail.
How do you install interior stair stringers?
To attach the stringers, nail through the plywood hanger and into the plumb cut of the stringer. The top of the stringers can be toenailed into the floor framing. Line up the temporary treads with the front and outside edges of the stringers, and nail them in.
Can you make a stringer out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
What size lumber are stair stringers cut from?
Selecting stringer stock Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.
What size lumber do you use for stair risers?
Stair stringers are cut from 2×12 lumber. For exposed side stringers, use cedar lumber. Make one stringer for each 16 inches of stair width. Allow for light boxes if riser lights will be installed.
Can I use deck pier blocks instead of footings?
Pier blocks can be used instead of footings for a ground-level deck not requiring permits. Piers blocks can also be used if the frost level depth is less then the height of the pier block.
What is code for steps on decks?
Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back. Stair treads must sustain a weight of at least 300 pounds in an area no more than four inches square.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
How high is a 2 step Stringer?
Size:2 In. Step stringers are cut for 2″ X 12″ Treads, and have a 7″ Rise.
Do deck stairs need footings?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
