QA

Question: How To Install Shoe Molding

Is it easy to install shoe molding?

Shoe molding covers the gap between the bottom of the baseboards and the floor. It’s an easy installation that costs little and gives your floors a precise, polished look. Carpenters like to use these bottom trim pieces because they reduce the need for complicated baseboard scribe cuts.

How do you install shoe molding without a nail gun?

On a clean work area, lay down the shoe molding face down and apply a bead of liquid nails in a zig-zag pattern so it covers the length of the molding. Put the molding up to the wall with the adhesive side facing the wall and press firmly into place. Carefully make sure everything is lined up.

What’s the difference between quarter round and shoe molding?

Quarter round is exactly as its name implies, one quarter of a round dowel. Shoe molding is much the same as quarter round, having the same 90° angle on the backside but instead of being a perfect quarter radius, its profile is a bit more squat.

Do you put quarter round on baseboards?

If you’ve been looking at baseboard finishing trim, you’ve probably discovered quarter-round, too. While quarter-round can be installed along the bottom of baseboard, trim carpenters and homeowners tend to prefer the sleeker look of shoe molding, which is taller and narrower than its curved counterpart.

Can I use quarter round instead of baseboard?

Sure, you can use quarter round without a baseboard as long as the crack you’re covering stays behind the quarter round. It is a plain, simple, clean look.

What nails do you use for molding?

The most common size used in moulding is 1-1/4″ (3d) or 1-1/2″ (4d) finishing nail. Select a galvanized or stainless steel nail for outdoor use. Nail Set: use to drive the nail below the wood surface without marring the moulding. Hammer: allows you to drive a nail into a piece of moulding.

Should I nail or glue baseboards?

Installing baseboards with a combination of baseboard adhesive and finish nails creates a tight connection between the wood and the wall. The adhesive prevents the wood from bowing out between the wall studs, while the nails keep the boards locked into place while the glue sets.

What is the difference between a brad nail and a finish nail?

Finish nails, or finishing nails, are generally made of 15- or 16-gauge steel wire, making them slightly thicker in diameter than brad nails. The added thickness means that finishing nails create a stronger hold than brads. The greater diameter of finish nails leaves a wider hole after fastening a piece of wood.

Should you glue or nail quarter-round?

A: Quarter-round should be nailed to the base boards only. It is intended to hide gaps between the base and floor. It should also permit a little movement in the flooring. Plus, it absorbs the impact of feet and furniture legs, so you may want to replace it sometime—thus, don’t glue it.

When should I use shoe molding?

Moldings are used to cover the expansion area, to hide cut ends, to adjust height differences or transitions between floors and to aesthetically finish the area.” Using shoe molding gives the floor installer more latitude in their end cuts and also allows you to hide the expansion gaps between the wall and the floor.

What size shoe molding should I use?

Consideration #1: The scale of your house–The most typical dimensions of quarter round are ¾” x ¾” while the most common size of shoe molding is ½” x ¾”.

How much does shoe molding installation cost?

Indoor Trim & Molding Cost Calculator National Average $1,310 Typical Range $604 – $2,049 Low End – High End $200 – $6,000.

How do you install shoe molding on an uneven floor?

6 Easy Steps for Installing Baseboard Molding on Uneven Floor Step 1: Grab the tools. Step 2: Prep the Baseboards. Step 3: Attach the baseboard on the wall. Step 4: Optional, Install Quarter Rounds. Step 5: Fill in the uneven gaps. Step 6: Paint the baseboards.

Do you always need quarter round?

One of the most common questions people ask is if they really need the base shoe, or if it’s just an add on. The answer is a simple yes. Without it, there is typically a gap between the trim and flooring, which is not only unattractive but makes it extremely easy for dirt and debris to build up under the base trim.

How far apart do you put nails in quarter round?

Tip. Choose finish nails that are long enough to penetrate the thickness of the quarter round molding and the drywall with enough left over to go at least 1/2 inch into the wall’s base plate. Place the nails no more than 18 inches apart for 3/4-inch molding.

How much quarter round is needed?

determine the perimeter of your room: add the length and width measurements together and multiply by two. Measure the width of each archway and doorway, and add together. subtract the total of the doorway widths from the room perimeter to determine the total required length of wall trim and quarter round molding.