Table of Contents
How do you install a rubber roof yourself?
Roof Deck Preparation. Clean the roof surface prior to installation. Install Drip Batten. Install the Drip batten wherever a gutter is present. Install Drip Back Drip Trim. The Drip Trim has a front and back piece. Chase out Wall Upstand. Relax Rubber Membrane. Fold Membrane Halfway. Apply Deck Adhesive. Sweep EPDM Membrane.
Do you have to glue down a rubber roof?
When you are fitting an EPDM roof, you need to make sure that it is glued down properly. During the membrane application process, you will need to apply two different types of adhesive. The first is a water-based adhesive. Use Permaroof deck adhesive for the best results.
Can I put rubber roof on plywood?
You can install EPDM membrane over an existing roof only if a new layer of 5/8″ plywood, 5/8″ OSB board or polyisocyanurate board with a fiberglass backing is used as a barrier to protect the EPDM.
Can EPDM be installed on plywood?
EPDM rubber roofing can be installed to a few different surfaces, but it works best when it adheres to timber deckings such as roofing grade plywood or OSB sterling board. Sometimes EPDM can be bonded to lightweight concrete and other surfaces that are non-porous like fibreglass and tissue faced insulation.
What is under a rubber roof?
Underlayment is a waterproof or water resistant barrier that’s installed directly to your roof deck before the actual roof material is installed. Here are some good reasons to use underlayment: It provides protection for the roof deck before and during the installation process.
How long does it take to lay a rubber roof?
How long does it take to install? The average (20m2) rear extension should only take a morning to install. Getting the roof stripped off and any decking replaced if needed usually takes longer than installing the Firestone RubberCover EPDM.
Can you walk on rubber roof?
Yes to an extent. EPDM is designed to take LIGHT foot traffic during installation and for occasional cleaning or maintenance. If you require more use than this, i.e. for a balcony then there are additional materials that can be laid over your EPDM for a more durable solution.
Can you lay rubber roof in rain?
Although installing an EPDM rubber roof is far easier and doesn’t require any specialist tools, the conditions have to be dry. If the surface is damp or wet, the EPDM products and membrane won’t successfully adhere to the surface.
What adhesive is used for EPDM?
Which industrial adhesive can be used to bond EPDM rubber? Cyanoacrylate adhesive is practically the only choice if you are looking for a high strength bond. Permabond recommends its 105 grade cyanoacrylate for this troublesome substrate.
What temperature can you install EPDM roofing?
FullForce EPDM and TPO SA may be installed when ambient and substrate temperatures exceed 20 °F (-7 °C).
Does EPDM roof need to be glued?
While the rubber roofs are known to be durable, they also need maintained. EPDM roofs are fully adhered or as many call it glued down. The system is not attached mechanically. If you are set on a rubber roof, make sure the roofing contractor is fully trained and experienced in installing a rubber roof.
How do I bond EPDM to wood?
Pour some bonding adhesive onto the wooden surface and use the paint roller to spread it evenly. Apply adhesive to the EPDM membrane the same way. Let the adhesive dry for the recommended time.
How do you glue EPDM roofing?
There are two ways to glue EPDM rubber. One is to apply an adhesive designed for EPDM and the other is to use an adhesive tape made for the material. The adhesive tape, however, requires that an adhesive primer be applied to the rubber. Fortunately, the primer is applied in the same manner as the regular adhesive.
Does EPDM roofing come in white?
EPDM roofing is a very durable, long-lasting, synthetic rubber roofing membrane containing two primary ingredients. Ethylene and proplyene which are both derived from oil and natural gas. It comes in two primary colors which are black and white.
How long will rubber roofing last?
Rubber roofing, when installed professionally, can last 25 years or more. TPO and EPDM roof systems have similar lifespans of 20 to 25 years. High-quality TPO roofing that is reinforced with fiberglass can last even longer.
How much does it cost to install rubber roofing?
Rubber Roof Installation Costs The average range of cost to install or replace a rubber roof is between $6,000 and $18,000, with the average being around $12,000. And as you know, all sorts of factors come into play that can affect that price, such as the materials, labor, obstructions, and customizations of the roof.
