Table of Contents
Which side of tar paper goes down?
When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper’s two sides are noticeably different. One side is somewhat sticky, though don’t expect it to leave a glue-like residue on your hands. The other side is smooth like paper, and typically contains lettering and line markings.
How do you install roof underlayment?
How much do you overlap roofing paper?
Roofing Requirements Roofing felt is required to overlap 2 inches over the lower felt course. The overlapping felt creates a secondary barrier for moisture and wicks water away from the shingles above and the sheathing below. Therefore, a 2-inch overlap provides redundancy at the edges where the barrier is weakest.
Does flashing go over or under tar paper?
Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Does roofing felt have a right side?
Apply felt right up to the ridge or to no more than 4 inches below it. (Rather than cutting the felt horizontally to fit, overlap it by more than 4 inches.) Apply felt on the ridge so it overlaps at least 8 inches on each side.
How do you attach roofing felt?
Use a construction stapler or a hammer. Put fasteners at least every 8 inches; some suppliers recommend staples about every 4 inches. Leave the top portion of the paper loose. Overlay a second layer of felt 2 to 3 inches and fasten it through the overlay so it secures the top of the felt underneath.
How do you tar paper a flat roof?
Climb onto the roof and lay a second strip of tar paper above the first strip, overlapping it by about 5 inches. Tack it firmly in place. Continue overlapping strips up each side of the roof, leaving the peaks uncovered. Cover the peaks by laying the center of a strip of tar paper along the peak.
Is roof underlayment necessary?
Whether or not underlayment is required, it’s always a good idea because it provides the roof deck an extra layer of defense against damage. Without underlayment, this rain will soak into the roof deck and cause problems ranging from mold and rot to leaks within the home’s interior.
Do you nail down roll roofing?
Do you nail down roll roofing? Nails are typically used to secure this type of roof. You can nail the separate layers by hammering the nails in 10-inch intervals across the roof. After that, you’ll want to use cement to cover them and seal them in place.
Can roofing overlap felt?
Always ensure there is at least 5cm of overlap between each sheet, and nail down the felt from the centre outwards as before.
Does roofing felt go under or over flashing?
1 Answer. It depends on where the drip edge is. At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.
Is tar paper needed under shingles?
Roofing felt or felt paper, also called underlayment or roofing tar paper, goes between the roof deck and the shingles, which adds another layer of protection to your roof. It serves as a water repellent when heavy rain and storms can cause moisture to get trapped between the shingle and wood of your roof decking.
What nails do you use for roofing felt?
Galvanised nails can be used in a wide range of applications, but are most commonly used in the installation of asphalt shingles and felt on outbuildings, sheds and more – wherever adverse weather conditions are common, galvanised nails are a good choice.
Does roofing felt need to be glued?
The reason you should use adhesive sparingly is because the bitumen in the shed felt will expand in warm weather and it will contract in cold weather. Not using too much adhesive allows it some give, which prevents it from tearing or cracking.
Can you staple roofing felt?
Tack or fasten roofing felt using stainless steel ¼” to ½” T50 staples or 7/8” to 1-1/2” hot-dipped galvanized or aluminum 12-gauge shank roofing nails with a 3/8” head diameter. Use the nails with or without plastic caps.
What is the difference between tar paper and roofing felt?
Tar paper is a heavy-duty paper used in construction. Tar paper is distinguished from roofing felt, which is impregnated with asphalt instead of tar, but these two products are used the same way, and their names are sometimes used informally as synonyms. Tar paper has been in use for centuries.
How do you finish felt edges?
To fix wavy edges More washing. Using a washboard or solar pool cover to provide the maximum agitation, wash and scrub just the edges. Roll with doweling. Furl the edges. Ironing the felt flat. Cut a straight edges around the felt. Felt areas to shrink them straight. Furl the edges of the felt. Pull the felt into shape.
Should I use 15 or 30 lb felt?
If your roof does not have a steep pitch, you can use #15. This weight of felt is a good economic choice if you have a standard roof. But if your roof has a steep pitch, #30 is a better option because it is thicker and tears less during installation. With #30 you get a thicker layer of underlayment and protection.
What is the best adhesive for roof felt?
Answer: Bostik Bituminous Felt Adhesive for Roofs is a cold applied adhesive for bonding bituminous roofing felts to asphalt, felt, metal and concrete.
