Table of Contents
Steps For Installing Rigid Foam Board On Exterior Walls Gather Your Tools And Equipment. You will need the following: Prepare The Concrete Wall. Measure The Wall. Cut The Rigid Foam Sheets. Install The Rigid Foam. Seal The Joints. Apply Spray Foam To Fill In Any Gaps. Apply Paint To The Installed Rigid Foam.
How do you insulate outdoor concrete walls?
The best choice for insulating the exterior face of a concrete block wall is some type of rigid foam board. Cover the concrete block wall with a good moisture barrier; some type of liquid asphalt or cement-based sealant is often used, but a tar paper or similar membrane also can be used.
Do you need a vapor barrier with rigid foam insulation?
What I recommend to create a thermal break in basements is rigid foam insulation, with TUCK tape and no vapour barrier. Tuck tape all seams AND, be sure to use a spray foam in all the corners. You don’t need vapour barrier, and you won’t need to insulate between the studs.
How do you glue styrofoam to concrete?
How to Glue Styrofoam to Concrete Walls Place a small amount of the construction adhesive on a hidden portion of the styrofoam and allow it to dry. Apply a thick line of construction adhesive around the perimeter of the styrofoam surface that will contact the wall.
Can you glue foam board insulation to concrete?
Cut the tip of a tube of low-VOC foamboard adhesive with a utility knife. If the adhesive doesn’t set quickly, you can drive one 1 1/2-inch concrete nail through the top of the panel and another through the bottom to hold it in place until the adhesive sets.
Can you spray foam directly on concrete?
The best way to insulate the interior side of a basement wall is with foam insulation that is adhered to or sprayed directly on the concrete. Any of the following insulation materials are acceptable for this purpose: closed-cell spray polyurethane foam or either XPS, EPS, or polyisocyanurate rigid foam.
Can you put rigid foam insulation between studs?
Rigid foam board insulation can be used throughout the home, but most often it is found in basement walls. The correct method of using rigid foam is to run continuous 4-foot by 8-foot sheets of the foam across the concrete basement wall between studs.
How do you install rigid foam insulation on a concrete floor?
Apply two coats of epoxy paint over the existing slab. The area should be clear of dust and debris. Install rigid foam insulation (XPS or EPS Type II) with the seams taped (see Figure 3). Install 1×4 furring strips at 16 inches o.c. and attach them to the concrete slab through the rigid foam insulation.
Is rigid foam insulation waterproof?
Technically, EPS and XPS rigid foam board insulation are considered to be water-resistant. A product branded as waterproof means that it offers complete impermeability, even if permanently immersed in water.
How thick should foam board insulation be?
Most panels range between 3/8″ and 2.5″ in thickness, though other dimensions and thicknesses are usually available through custom order.
What is the R-value of 2 inch foam board?
A wall utilizing STYROFOAM T-MASS Technology with a 2-inch exterior layer and a 4-inch interior layer of concrete along with a 2-inch layer of STYROFOAM extruded polystyrene insulation would result in a material R-value of approximately 11.33.
Do you need house wrap over foam board?
The answer, happily, is yes. In fact, the two products combined make your home super-insulated from outside wind and weather. If you choose to install house wrap with rigid foam, generally, it should go under the insulation, not around it.
What type of fasteners are used on rigid insulation?
PRODUCTS USED IN THIS APPLICATION Thermal-Grip® ci Prong Washer. 2″ diameter washer used for attaching continuous rigid insulation (ci). Plasti-Grip® PMF Anchor. Pos-I-Tie® Veneer Anchoring System. Thermal-Grip® Brick-Tie Washer. Grip-Lok® Hurricane Washer.
How do you attach foam board?
To attach the insulation, you can use screws with large washers, a special adhesive made for adhering foam board insulation or, for smaller pieces, you can seal them in with caulk or spray foam.
What is the best adhesive for foam board?
Sculptors and Multimedia Artists Use the Best Adhesives for Foam Liquid Nails Latex Adhesive. Liquid Nails is an extremely strong construction adhesive for use with foams and plastics. 3M Foam Fast Spray Adhesive. Wilsonart Water-Based Adhesive. Loctite Foamboard Adhesive. 3M Fastbond Contact Adhesive.
Which is better EPS or XPS?
XPS, at about R-5 per 25 mm, has only a slightly better thermal performance than EPS. However, EPS with the same level of density is less expensive. XPS is usually avoided in areas where materials with less density are needed or where the material, which is not produced below a certain density, is not applicable.
What screws do you use for foam board?
Screws that are 2 1/2 inches long are appropriate to attach 2-inch thick foam board to 3/4-inch thick plywood.
How do you attach foam board insulation to studs?
Apply a bead of construction adhesive to the part of the studs you will cover with the first sheet of insulation. Press the insulation sheet firmly in place, and hammer cap ring-shank nails into the studs at 6-inch intervals.
Why do they put foam under concrete?
This is to stabilise the slab beneath the building. This results in more concrete being used, as well as an increase in labour to prepare the site for the concrete pour.
How thick should spray foam be on basement walls?
The thickness of foam insulation in basement walls will range between two to seven inches, depending on where you live and whether you use open or closed-cell spray foam insulation.
Can you use foam insulation on basement walls?
The best way to insulate the interior side of a basement wall is with foam insulation that is adhered to or sprayed directly on the concrete. Any of the following insulation materials are acceptable for this purpose: closed-cell spray polyurethane foam or either XPS, EPS, or polyisocyanurate rigid foam.
How do you insulate an exterior wall?
To add insulation to any exterior wall, holes are drilled between the studs of the existing walls. Then, spray foam, cellulose, or another form of loose-fill insulation can be blown in to fill up the wall cavities. Finally, the holes must be plugged up and refinished to match the rest of the wall.
Do concrete walls need insulation?
Homes that have concrete walls in the basement or elsewhere still need insulation and weatherproofing for the owners to enjoy increased energy savings. However your basement walls are constructed, you’ll likely want to insulate them.
