Table of Contents
What are the steps to installing a metal roof?
Step-By-Step Step 1: Measure the roof area. Step 2: Order the materials. Step 3: Remove the old roof. Step 4: Add insulation. Step 5: Install the eave flashing. Step 6: Metal Roof Installation: Add metal panels. Step 7: Add the flashing to the roof. Step 8: Finish.
Can I install a metal roof myself?
While most metal roofing styles can be installed as an advanced DIY project, metal roofing installation is complicated and can vary slightly based on the brand of panels or shingles that you select. We recommend that you install a metal roof with one or two helpers and fall protection equipment designed for roof work.
Do you have to put plywood under metal roof?
As long as the interior of your roof is protected from moisture accumulation, underlayment is not required, though homeowners planning to insulate their house heavily may choose to install plywood to protect their investment.
Can you put metal roofing directly on plywood?
Metal roofing should not be installed directly over the top of bare plywood. You do not have to install roofing shingles or other roofing material, but a felt sheet over the plywood is the bare minimum. When the metal expands or contracts with changing temperatures, it can tear or wear away the felt sheeting.
Where do you put the screws on a metal roof?
And most U.S. metal roofing manufacturers say that you should put screws into the flat, because this location offers a solid wood surface just beneath the metal panel, resulting in a safer, tighter, more secure seal.
Does a metal roof need strapping?
Single wood strapping is better than no strapping, as it creates a wider gap between the existing roof decking and the metal roof, but doesn’t afford enough ventilation to resolve condensation issues. It also does not allow leveling of the roof, which corrects swells and swales on the roof.
How often do you screw metal roofing?
Corrugated roof panels and other exposed fastener metal roofs are usually held together with screws every 18 inches or 2 feet. You will want to note your metal roof screw pattern, so you know where to look for potential problems.
What do you put down under metal roofing?
The traditional and most common material used for roof underlayment on a steep-slope metal roof is non-perforated, asphalt-impregnated felt underlayment. There are several types of felt underlayment including both organic reinforced and inorganic reinforced.
Do I need furring strips under metal roof?
When installing a metal roof over an existing roof, insulate the spaces between the wood strips with rigid insulation to prevent condensation before installing the roofing. You also need to add furring strips. Twenty-four inches is a common spacing of furring strips for a metal roof.
Do you need a vapor barrier under a metal roof?
To avoid condensation buildup with your metal roof, you will need to have a moisture barrier in place. It depends on air temperature, water vapor near the metal panels, the prevalence of warm air in and around your roof assembly, and other conditions.
Can metal roofing be screwed to OSB?
No, you do not need to screw into solid lumber (joists, stripping,etc.). As you can see, the thinnest material they recommend is 1/2” (7/16”) OSB board at 9” on center up to 24” on center. Be sure to follow their instructions in order to obtain the warranty.
Do you need felt paper under metal roofing?
Metal roof underlayment is an important component of a metal roofing system. Some might choose to skip using underlayment to save money. However, the metal roof underlayment acts as an added layer of protection. The short answer is yes, your metal roof does need underlayment .
Do you need OSB under metal roof?
The simple answer is yes, your roof does need an underlayment. Traditionally built homes will need an underlayment. If your home is built with joists, insulation between those joists, and sheathing, then an underlayment is needed before you put on a metal roof.
What is the screw pattern for metal roofing?
Lap screws are spaced 12” to 18” on center. The panel screws are spaced out so that every third corrugation has a screw including both sides of the panel sidelap. When the corrugated sheeting is 39” wide instead of 37” wide the screw placement will be slightly different as shown in the diagram below.
How much should a metal roof overhang?
A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.
Is it okay to overlap metal roofing?
Metal roof panels are designed to overlap with one another, helping you keep water from leaking where two panels meet. The amount of overlap that is required generally depends on the overall slope of your roof. During the installation process, start by calculating the pitch of your roof.
Can you walk 29 gauge metal roof?
Generally speaking, it is as safe to walk on a metal roof 30 or 50 years after installation as the day it was installed.
