Table of Contents
Do you install stair treads or risers first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser.
Should you nail or screw stair treads?
Don’t fasten treads and or risers with only nails or staples. The adhesive is much more important than the fasteners. There will be times when fastening may be limited, so a good adhesive is critical. Rely on the front edge of the riser for your level surface.
Where on the stairs do you start when installing risers and treads?
Some contractors prefer installing the riser first, then installing the tread against the riser, fastening the riser to back edge of the tread with screws (Diagram A). Others prefer to place the tread first and place the riser on top of the tread, for additional support (Diagram B).
How far should a tread overhang the riser?
Stairs must have an overhang between 3/4″ to 1-1/4” to increase the depth of the step, making it better for descent while maintaining a clear 10-inch going for the ascent. Treads that are 11-inches deep or greater do not require an overhang.
Do risers go behind or on top of threads?
4 Answers. The riser is installed first for the reason that you want a nice tight fit along the top of the riser to the tread above it. There is always the possibility that there is a small variation in the width of the riser boards or the height of the notches cut in the stair jacks.
How do you attach stair treads?
Measure each tread and cut it to size then install it using 2-1/4″ trim screws. installing the treads. Install the Treads. fill in screw holes with wood putty. Fill Screw Holes. mark stair railing for angled cut. Cut Railing to Length. pre drill landing and treads for balusters. attach rail fasteners into newel posts.
Can you just glue stair treads down?
NO!!! As someone who’s done a lot of hardwood flooring, as well as stairs, adhesives are not enough to hold a stair tread down. Treads should be attached with a combination of adhesive and nails. Nail length being a minimum of twice the thickness of your tread and of 16 gauge or larger.
Which adhesive is best for stair treads?
A polyurethane glue, such as Loctite PL Premium, is a highly recommended adhesive. Since the stair treads, or the surface of your stairs, receives a lot of foot traffic, you’ll want to make sure it’s properly installed.
What screws to use on stair treads?
Use screws that are between 2 and 4 inches long. Deck screws are available in this size range, and are used for this purpose on deck stairs. Drilling pilot holes will help prevent splitting the wood of the stringers.
How much overhang should there be on a stair tread?
The nosing on treads, believe it or not, has a code minimum and maximum of how far the nosing projects over the next stair. Nosings are required to overhang a minimum of ¾-in. to a maximum of 1-¼-in. Also the maximum nosing radius cannot exceed 9/16 of an inch.
How do you fasten stair risers?
Install the first riser, beginning at the bottom of the staircase. Spread a thin coat of construction adhesive across the middle of the back of the riser. Attach the riser to the plywood with three nails spaced vertically along the left and right stringers, with a third line of nails along the center stringer.
Can I use 2×12 for stair treads?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
Why is nosing required on stairs?
Nosing provides a larger surface area to step on, which makes walking up and down much easier. Stair nosing helps protect the most exposed areas of the stair tread from damage and general wear. In the case of wooden or concrete stairs, this is especially important as the tread may chip or break if heavily used.
What is code for stair height?
(1) The rise of every step in a stairway shall be not less than 4 inches nor greater than 7 1/2 inches. (2) The run shall not be less than 10 inches as measured horizontally between the vertical planes of the furthermost projection of adjacent treads.
Is pine or oak better for stairs?
Oak’s fine texture make it ideal for treads that will be stained and left uncarpeted or for those that will be covered with a carpet runner down the center, such as the main staircase in a home with matching hardwood floors. Because it is more porous than oak, pine is the preferred wood for stairs that will be painted.
How do you fill the gap between stair tread and riser?
Riser-to-Tread Gap Place the cove molding face up across two sawhorses. Measure the width of the stair tread where it meets the riser. Apply a bead of construction sealant to the back of the molding. Apply colored silicone caulking to stringer gaps. Cut the tip off of a tube of colored silicone with a utility knife.
How do you widen stair treads?
Cut ¼-inch round over hardwood molding, ¾ inch wide to fit the front lip of each step and nail it to the lip of the step with pin nails to cover the screw heads. This process will extend your stair treads 1 inch.
