QA

How To Install Hi Lo Converter

Does a line out converter need to be grounded?

A: You don’t have to unless the loc is powered. With this, you just need left and right speaker to tie into. You can ground it if you want, but you do not need too.

How do you install a rear output line converter?

Can I use both high and low level outputs?

No, it is not recommended connecting the High Level and the Low Level simultaneously. These two inputs are run on the same circuit internally on the REL and will result in far too much gain. 1 circuit at the same time for surround sound applications. Nov 23, 2020.

How do I connect my subwoofer to left and right input?

To connect a subwoofer to its receiver, you can use an LFE input cable or an RCA line-in cable (used for left and right input options). Assuming your subwoofer has the option to use an LFE input, this will be your best choice. But, if not, then an RCA input option will work.

Is a line out converter necessary?

A: Yes, definitely. Amplifiers that offer speaker-level inputs don’t require a separate line output converter to tap into existing speaker wires to get their signal. This amp includes an adapter that lets you connect your speaker wires directly, without needing a line output converter.

What is the blue wire on a line output converter?

* Yellow will get a 12 volt constant power. Wire this into the power wire you have feeding your amp and fuse it seperately with a 5 amp fuse. * Blue black connects to chassis ground. If possible use the same ground as the amp to prevent ground loops.

Does an LOC need power?

LOCs are the original integration pieces in car audio. The most basic ones are passive devices. These units have been around since aftermarket car audio became a viable market. They work in a lot of basic vehicles but they have no feature set and they typically aren’t built to handle much input power.

Do RCA cables go to input or output on AMP?

Your amplifier gets its input signals from the receiver’s output typically via RCA cables. RCA cables come in stereo pairs, in various lengths. When running new speaker wires from your amplifier’s output to the speakers, any size wire from 18- to 14-gauge will work fine.

How do I tap into my rear speakers?

Some (many) powered subs have high level inputs, so you can just tap into the rear speaker wires. If your car has a factory sub, use its speaker wire instead. If it doesn’t have high level inputs, you can use a basic line out converter that ties into the speaker wires and turns them into a rca output.

What is the difference between high level input and low-level input?

Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the amplifier with the source unit. Because high-level inputs require that you splice into your vehicle wiring, some users forgo that option and prefer to run the RCA cables instead.

What is a low-level audio signal?

Low-level audio is typically classified as an “un-amplified” signal – usually 4 Volts and lower – transmitted through RCA cables (Fig. There are premium source units on the market capable of higher output voltages on its RCA output jacks than specified above, but these are a special class of radio.

Should I use both inputs on subwoofer?

Dual input allows the subwoofer an extra sensitivity adjustment. Normally, it would be enough to use a mono LFE subwoofer signal from its processor. By using both inputs with the same mono signal doubles the subwoofer sensitivity. This means that there is now only half the signal strength to drive it to full output.

Can you wire a subwoofer to the both right and left channels?

Can you wire a subwoofer to both right and left channels? – Quora. Yes. You can use the speaker level inputs and tap the red right and white left wire. You can also use the RCA sub out or pre amp sockets and connect both red and white to the sub.

What side does a subwoofer go on?

For the best sound quality, the subwoofer should be placed with the speaker facing out to the room, and the port should be away from a wall. Bass waves travel in all directions, but it’s important to have the speaker facing your main listening area.

How do you hook up subs to a factory radio?

8 Steps To Install A Subwoofer To A Factory Stereo Step 01 : Gather all necessary equipment. Step 02 : Choose a speaker and an amp. Step 03 : Remove the battery from the vehicle. Step 04 : Disconnect the wires of the speaker. Step 05 : Identify the relevant connections. Step 06 : Run wires. Step 07 : Reinforce the connections.

Can I connect speaker out to line in?

3 Answers. You can safely connect the Green (normally “Line Out”) to the Blue (normally “Line In”). The Pink (normally “Mic”) input is generally designed to handle more amplification and since line-out operates at higher levels, you would likely overdrive the signal and not be able to hear anything anyways.

What voltage is speaker level?

What is Speaker Level? Speaker Level is also measured in volts, typically using over 10V. The physical size and power handling of the speaker, combined with the volume set by the output, can push this number up to 100V or more.