Table of Contents
Can Hardie backer board be used in a shower?
Installing cement backerboard is one of the more popular choices for a shower wall substrate. Cement backerboards include Hardiebacker, Durock, Fiberboard, wonderboard, and similar products. When installed properly they will give you many, many years of durable shower construction.
Does Hardie board need to be waterproofed?
Hardiebacker (James Hardie): the use of a waterproof membrane, vapor barrier or vapor. retarding membrane is optional unless the local building code requires it.
Does backer board go under shower pan?
The wallboard must be installed 1/8 inch above the shower pan. If the shower pan is not in place, the wallboard height must be guessed, which can lead to inaccuracies and an expansion gap that is too large or too small.
How do you attach Hardie board?
Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom.
Do you need put plastic behind cement board shower?
plastic behind cement board with waterproofing is essentially suspenders when you already have a belt. the waterproofing is also a vapor retarder so if the red guard or kerdi product is continuous, lapping corners and all, the plastic will be unnecessary.
What happens if Hardie board gets wet?
If Hardie is installed too close to these surfaces, there is a chance that the paint will start to bubble and peel. This happens because the boards are wet almost all the time, and the water in the board will start to expand and contract as the temperature changes.
Do you need waterproof membrane on cement board?
Contrary to popular thought, tile and grout are not waterproof, and some moisture will penetrate even if sealant is used. However, if you choose to use concrete backerboard, which is much stronger and more durable than gypsum board, a water vapor membrane must be placed underneath it or a sealant applied on top of it.
Does Hardie board need a vapor barrier?
Depending on your local building authority having jurisdiction (the AHJ) over your building codes, vapor barriers are almost always required, whether your builder uses James Hardie products or some other, inferior product.
Should I wet Hardibacker before tiling?
A. To be more precise, I’ve installed lots of concrete backer board for years, all with good results. The concrete is unaffected by any water that manages to get behind the ceramic tile. If you use cement backer board, you have to install a separate moisture barrier between the board and any wood it’s attached to.
Should I use RedGard on Hardibacker?
You really don’t need the RedGard, but the more protection the betterso go for it. And yes, you can do the boards beforehand. But, hit the filled seams & screws (your weak points) as soon as a panel is ready to give it some time to setup. You’ll have to wait for the fills to dry or at least setup anyway.
Does backer board go over shower pan lip?
The best approach when installing cement board or other tile backer around a tub is to keep the cement board out of the lip area. above the lip of the tub. Then apply a generous amount of thin-set to the bottom bathtub tile and position it 1/8 in.
What goes first shower pan or walls?
Whether you choose to install tile or the panel walls, drywall always goes on top of the shower pan, after the pan is set into the floor. Both tile and shower walls perform the same function, they just do so with different types of materials.
Do you waterproof under a shower base?
DON’T ignore the importance of waterproofing when installing an acrylic shower base. The walls and the area around the top of the acrylic base along the wall are very important for proper waterproofing and it is essential that it be done correctly. In a bathroom, proper waterproofing is non-negotiable.
Do you nail or screw Hardie board?
What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.
Can you use screws on Hardie board?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. Fasteners shall be installed between 1 in. and 3/4 in.
Can you install Hardie board yourself?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
What do you do with a gap between tub and cement board?
Technically, after the tile is installed over the backer board that gap between it and the tub ledge should be filled with an ASTM C920 sealant (caulking e.g. silicone). Although some say you should have weep holes along this gap so any water behind can weep out into the tub.
Is Hardibacker good for shower walls?
3 Answers. 1/4″ hardibacker alone is an unsuitable substrate for shower wall tile. If it were attached to properly waterproofed drywall, plywood, or plaster it would be fine. Think about it, one wayward elbow, knee, or hip bump and you may get flexion which would cause the grout (or tile) to crack.
