Table of Contents
Is gutter apron and drip edge the same thing?
A gutter apron serves the same purpose as a drip edge. As such, gutter aprons are intended to direct water away from potential problem areas of the house, down to the roof edges, and into the gutters. Like drip edge, a gutter apron may be available in many different colors.
What is a roof gutter apron?
A gutter apron is a long piece of metal fold that starts under the first course of shingles and hangs over the sheathing of the roof. Gutter aprons take on an additional role by hanging down an inch or so into the back of the gutter to prevent water from dripping or splashing behind the gutter.
Do I need drip edge with gutters?
If the home has no gutter, the drip edge will prevent the water from running down the fascia and onto or into the soffit cavity. However, without the drip edge, the water sticks to shingles, potentially working its way under the shingles to cause a leak.
What is the difference between drip edge and rake edge?
It involves the point of application in relation to the underlayment and/or eaves flashing. At the rake edge, the perimeter drip edge metal is applied over the underlayment with the appropriate fasteners secured every eight (8) to ten (10) inches on center.
When should gutter aprons be installed?
A gutter apron is installed under your starter shingle course and is even more useful if your roof shingles don’t extend far enough to direct rainwater into the gutter. Gutter flashing also protects the back of the gutter, since gutter aprons are installed by hanging down an inch below the back of the gutter.
Why does water run behind my gutters?
Water Gets Behind the Gutter If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter. aluminum flashing.
What is the metal behind a gutter called?
Danny Lipford: Everybody knows how important your roof is to protect your home from the weather, but you might not realize how important this little metal strip is to your overall roof system. It’s called eave strip or eave metal.
Do you need gutter flashing?
Why Flashing is So Important Flashing creates a seal between your gutters and your roof line, which allows water to flow off your roof and into the gutter. Without it, some water would also flow behind the gutter, which would damage the building surfaces beneath the roof.
How much should shingles overhang drip edge?
Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.
Should there be a gap between drip edge and fascia?
The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger. The shingles should also overhang the drip edge 3⁄8 to 1/2 an inch.
Where should drip edge be installed?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
Does drip edge go over or under underlayment?
According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof. But over the underlayment along the rake edges of the roof. Understanding the proper way to install the drip edge will only get you so far.
What is a roof Eve?
An eave is the edge of the roof that overhangs the exterior siding. Parts of an eave include the soffit, which is the underside of your roof’s eaves, and the fascia, the vertical facing board.
How far should metal roof overhang?
A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.
Do gutters go on rakes or eaves?
Rain gutters should be positioned to extend beyond the eaves of a roof to collect rain and hail runoff. Gutters are placed on all sides of a home along the roof edge.
Can drip edge be installed later?
The most popular time to install a drip edge is when new shingles are installed. However, the drip edge can be installed at any time. The materials involved include: a ladder, a flat pry bar, a hammer, tin snips, eave stripping, and galvanized roofing nails.
What does drip edge flashing do?
Drip edge is metal flashing installed at the edges of the roof to keep water away from your fascia and from getting underneath your roofing components. If your roof doesn’t have drip edge, water gets behind your gutters and rots out both your fascia board and roof decking.
What is a gutter flashing?
Gutter flashings are installed beneath the roof line and inside the gutter itself. This will prevent water from running behind a gutter and leaking into the building materials causing damage. They are usually 10 feet long, but can be made to fit specific roofs.
Should you caulk gutters?
Caulk is a necessary part of gutter maintenance. The seams of your rain gutters can rust if left unprotected and fungi can begin to grow in the seams if rotted leaves or other organic matter gets caught in the cracks.
