Table of Contents
How are fireplace surrounds attached?
Fireplace surrounds are typically hollow structures (as shown below) and so can be attached to the wall with metal brackets located at the edges of the surround, or even screwed onto another piece of wood that’s already joined to the wall.
What is the surround around a fireplace called?
The mantel is located at the top of the fireplace surround, or top of the face of an open fireplace. The mantel provides a shelf on which decorations and other items can be placed, but can sometimes help with preventing smoke from the fire from coming into the room.
How do you install a cast iron fire surround?
Fitting cast iron inserts with wooden surrounds Place the insert on top of the hearth in front of the fire back. Place the surround against the insert. Use a pencil to mark the position of the surround on the wall. Remove the surround.
How do you secure a fireplace mantel to Brick?
Mark where the anchors or brackets line up on the mantel and drill the corresponding holes. Lift the mantel and place it so that the lag bolts or brackets fit into the holes. For extra security, coat the tip of each bolt with liquid nails or another adhesive just before installation.
What can I use for a fireplace surround?
Material Choices for a Fireplace Surround STEEL. Steel is one of the most popular fireplace surround materials. WOOD. Wood is a less obvious choice for a fireplace surround than steel.. CONCRETE. STONE. BRICK. TILE.
Does a fireplace need a surround?
A fireplace does not always necessarily need a surround, but the requirements for a fireplace surround must be in line with local and national codes and building regulations. A fireplace can also look very bare if there’s no surround.
Are wooden fire surrounds safe?
Unless you are going to use twin wall flue to protect combustibles then I would suggest you refrain from considering wooden beams or wooden surrounds.
How do you tile a fireplace insert?
Steps for tiling a fireplace: Step 1: Prep the materials and layout. Step 2: Mix the mortar. Step 3: Spread and comb the mortar. Step 4: Lay the hearth tile. Step 5: Cut the tiles. Step 6: Lay the first surround tile sheets. Step 7: Cut the hearth tiles. Step 8: Grout the tile.
What is a floating mantel?
Our mantels are hollow on the inside, providing an easy alternative to solid wood mantels. Live grain end caps maintain the look of a solid piece of wood. Each mantel is hand crafted from reclaimed longleaf pine, providing a unique look and character that cannot be duplicated.
What is the best way to drill into brick?
Begin by drilling a pilot hole using a small masonry bit. Then, attach the larger bit and drill again to make a bigger hole. Make sure the drill is perpendicular to the brick wall. Drilling through brick and mortar places stress on the drill, causing it to heat up.
How much does it cost to build a fireplace surround?
A stone fireplace surround usually costs between $3,000 and $7,500 but could run anywhere from $2,500 to $10,000 or higher. The surround refers to any part of the fireplace built with stone, or the area surrounding the firebox.
Can you use MDF around a fireplace?
You can use paint-grade wood (such as MDF) or finish wood (cherry, maple, oak). The ends of that piece of moulding should be cut at 45-degree angles. Then, to complete the job, extend the moulding around the bottom of the mantel.
How do you hang a heavy mantle on drywall?
Holding your drill at a 45 degree angle downward, drill a pilot hole through the shelf and drywall and into the stud. Install a finishing nail into each of the pilot holes with a nail gun or hammer; the nails must be long enough to penetrate at least 1 inch into the drywall. These nails will secure the mantle in place.
How do you seal a fireplace surround?
Lie on your back facing up into the fireplace and look at the top of the fireplace surround. Using the loaded caulk gun, lay down a bead of caulk to seal any and all gaps that you find. With this silicate cement, use a generous supply to fill in the gaps.
How wide should fireplace surround be?
Your mantel should be wider than your fireplace. Typically, a mantel should be a minimum of 3 inches past the firebox on each side. However, more can be better. The average mantel is approximately 6 inches wider than the fireplace on either side, and some can be even wider.
Can you use cement board around fireplace?
Yes, HardieBacker® 1/4″ Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4″.
Can you use drywall around a fireplace?
Drywall + Fireplace = House Fire Unfortunately, this is highly flammable and is not an appropriate or safe fireplace surround. The sheetrock had to be removed and replaced with any type of non-combustible surround – stone, tile, marble, or metal.
What is behind fireplace surround?
What Is Behind A Fireplace Surround. The area around the opening of a fireplace is called the fireplace surround, and can be made from a number of different materials including wood, stone or metal. The fireplace surround was then removed, leaving behind the cast iron fireplace back panel and the gas fireplace insert.
Is shiplap safe for fireplace?
Many people may not realize that shiplap is perfectly safe to install in your fireplace surround if you follow the correct safety codes. Every state varies with its code for fire safety and surround materials.
