Table of Contents
What is the joist spacing for Fiberon decking?
on center. However, Fiberon recommends spacing the joists at 12 in. on center to increase stability and reduce the flexing of the deck boards.
How do you finish the ends of Fiberon decking?
Composite decking ends can be finished by picture framing, raised fascia board, painting the ends, attaching decking veneer, composite nosing strips, vinyl stair nosing cove, composite corner trim or plastic end caps. In short composite decking, ends must be hidden or blended into the look of the decking boards.
Do you leave a gap between composite deck boards?
As temperatures fluctuate, composite deck boards will naturally experience thermal expansion and contraction. That’s why the board ends should never be installed tight against one another. There should always be a slight gap.
How do you cut Fiberon decking?
Procedures Cutting: When cutting Fiberon Horizon Decking, remember to use a carbide-tipped blade with a minimum of 24 teeth. A frayed edge may result from dull blades or blades fewer than 24 teeth.
Does Fiberon decking expand?
This will vary from 1/32” in hot weather to ¼” in cold weather. All decking materials whether wood, composite or metal, will undergo some degree of linear expansion with the changes of weather and season. To compensate for the effects of contraction and expansion, maintain required installation instructions.
Can you rip cut Fiberon decking?
Can composite decking be cut? Yes, you can cut most composite decking just like wood — no special tools required.
How wide is Fiberon decking?
Fiberon ArmorGuard Deck boards are . 093 in. x 5.25 in. Grooved(for hidden fastening) deck boards are available in 12, 16 and 20 ft.
Do you need a special saw blade to cut composite decking?
Table saw blades with a 7 to 9 inch diameter and few teeth are best for cutting composite decking. Blades made specifically for cutting composite decking usually have a tooth design that makes them unique from the other ones. The material that is going to be cut should be kept in mind when selecting a jigsaw blade.
How should you stagger deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
What is the correct way to lay decking boards?
What is the correct way to lay decking? Any decking board manufacturer or professional will tell you: “The proper way to install a decking board is ridge side down.” The ridges are designed to allow for airflow, to stop moisture sitting in the ridge, and allow for a stronger structure.
Do you need to seal cut ends of composite decking?
Kim Katwijk The cut ends of composite decking will absorb moisture and can swell, as shown here. Sealing the end cuts with lumber wax will help prevent swelling. Because the uncapped ends of the boards are free to pick up water, the core can absorb moisture, which can lead to all sorts of problems.
What does Fiberon decking weigh?
Board Weight: 2.36 lbs./lineal ft.
Is Fiberon decking slippery when wet?
Fiberon Paramount Decking has a high slip resistance when tested according to ASTM F 1679 with a dry/wet rating of . 85/. 82.
Can you power wash Fiberon decking?
Pressure washing is best left to the professionals. If you choose to use a pressure washer on your Fiberon deck, use extreme caution! Ensure the pressure is less than 2,500 psi at 12 inches above the deck surface. Pressure washing is not recommended if mold or mildew is present on the deck.
Can you use Trex fasteners on Fiberon decking?
Fiberon Phantom universal plastic hidden fasteners are compatible with most leading decking brands. All other Fiberon fasteners are designed specifically for use with Fiberon decking products.Are Fiberon fasteners compatible with other decking brands? AERT® Moistureshield™ ChoiceDek™ TREX® Transcend® Enhance® Select® AZEK® Grooved PVC Vintage Arbor Harvest.
What are the problems with composite decking?
Common complaints from homeowners include their composite decking board swelling, shifting, warping, and shrinking. The cause of this isn’t exactly clear, but it’s suggested that the composite nature of the decking leads it to be much more sensitive to temperature and humidity swings as well as sun exposure.
How do you prevent deck boards from ripping?
Installing Deck Boards Without Ripping the Last to Fit The trick is in not cutting the joists to their final length until late in the game. I’d attach the uncut joists to the ledger and then start installing the deck boards at the house.
Can you use regular deck screws for composite decking?
You can screw or nail composite decking boards just like wood ones. Three-inch decking screws are the best fastener choice; they sink a secure distance into the joists and won’t back out like nails.
How does fiberon compare to Trex?
Fiberon and Trex are made with recycled plastic bags and other plastics combined with sawdust and other wood waste. Fiberon’s premium product lines have slightly less recycled content compared to Trex (about 2% less), but their more affordable boards are similar to Trex – about 96% recycled content.
What is the warranty on Fiberon decking?
Fiberon offers a five-year limited labor warranty on select products sold in the United States and Canada. With this coverage, if an eligible product fails to perform in accordance with its original warranty, Fiberon will pay reasonable labor costs associated with replacement.
