Table of Contents
How do you put a drip edge on a shed roof?
How to Install Drip Edge on Shed Roof Install eave drip edge by nailing it to the sheathing. Extend drip edge an inch at each end. Install roofing felt. Install rake drip edge over the felt. Nail every 12” or less. Rake drip edge overlaps the eave drip edge. Bend eave drip edge corners under rake edge.
Do you need drip edge on shed roof?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Is drip edge necessary?
The 2012 International Building Code (IBC) requires drip edges for that type of roof. Regardless of the kind of roof you have, we highly recommend installing drip edges. Keep in mind that improper installation of any roofing component can create gaps, rendering any waterproofing solution useless.
Does drip edge go around entire roof?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
Does drip edge go over or under underlayment?
According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof. But over the underlayment along the rake edges of the roof. Understanding the proper way to install the drip edge will only get you so far.
Should drip edge be tight against fascia?
A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.
What kind of nails do you use for drip edge?
The drip edge is nailed in place using 1-1/2 galvanized roofing nails. A felt-tip marker works great for marking cuts. And, again, prying open the end with a small flat bar allows the pieces to overlap cleanly.
How do you finish the top edge of a shed roof?
How to Finish the Top Edge of a Shed Roof For the final row, cut shingles into strips. Ensure strips are wide enough to cover nails. Install your strips. Apply sealant over exposed nails on the last strip. Use more sealant along the top edges of all shingle strips.
How far should shingles hang over drip edge?
Shingles should be installed over the drip edge a minimum of 3/8” (9 mm) at both the eave edge and the rake edge. If the drip edge extends… out from the rakes and eaves (typically called DL Style or D Type), the shingles may be installed flush with the drip edge.
Do you nail drip edge?
Owens Corning™ Roofing recommends installing drip edge on all roofs to be covered with asphalt shingles. Nail the drip edge to the roof deck with minimum 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches.
Can you install drip edge after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
Do you install drip edge before tar paper?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.
How much does it cost to install drip edge?
The cost of drip edge Drip edge is always going to be included in your roof replacement. Because of this, it’s going to have an impact on the price you’ll pay for your new roof. The standard drip edge used (aluminum) is going to be around $2.00 a linear foot, including labor to install.
Should I paint my drip edge?
The drip edge in and of itself is designed to protect the integrity of your roof, but that doesn’t mean it doesn’t also need its own protecting! Priming and painting will deliver that protection, along with a cohesive aesthetic if your drip edge is visible.
What size drip edge should I use?
Metal Edge Drip: A drip edge has to be resistant to possible corrosion and should be 36 gauge or larger.
Do I need a drip edge on rake edge?
A drip edge should be installed on the eaves and rakes of the roof, flush with the decking and fascia. On eaves, the drip edge is installed directly to the deck with underlayment installed over it for proper water shedding. On rakes, the underlayment is installed over the drip edge.
What is the cheapest way to roof a shed?
In most cases, MSR roll roofing is the cheapest shed roof material you can buy. Roll roofing is also the easiest shed roof to install because you can cover large areas quickly by simply rolling it out and nailing it down.
