Table of Contents
Does drip edge go over or under underlayment?
According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof. But over the underlayment along the rake edges of the roof. Understanding the proper way to install the drip edge will only get you so far.
Can you put drip edge on after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
Should there be a gap between drip edge and fascia?
The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger. The shingles should also overhang the drip edge 3⁄8 to 1/2 an inch.
How do you install drip edge flashing on a roof?
Does roofing paper go on before drip edge?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Where should drip edge be installed?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
Can you install drip edge without removing gutters?
If the home has no gutter, the drip edge will prevent the water from running down the fascia and onto or into the soffit cavity. However, without the drip edge, the water sticks to shingles, potentially working its way under the shingles to cause a leak.
Is drip edge on roof necessary?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
How far should shingles overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Should gutters go behind drip edge?
It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.
Do you nail drip edge to fascia?
You don’t. The drip edge is attached onto the plywood roof decking before any shingles are installed. And assuming that the roof’s bottom edge has a typical fascia trim, that trim should be in place before the drip edge.
How far should drip edge be from fascia?
Drip edge height: 1 5/8″ Drip edge lip extension: 1/2″ Recommended drainage gap: 1/4″ (approx) spaced off of the fascia board.
Does roofing felt go over or under drip edge?
1 Answer. It depends on where the drip edge is. At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.
Does flashing go over or under shingles?
Flashing should overlap the roof-covering material, but on asphalt shingle roofs, for aesthetic reasons, the part of the headwall flashing that extends down over asphalt shingles is often covered with a course of shingle tabs.
Do you need tar paper under shingles?
Answer: Roofing felt is a layer of tar paper installed beneath the shingles to provide a backup waterproof membrane in case of leakage. But don’t let the lack of underpayment become a major issue for you, because it is simply not required for a second layer of composition shingles.
What size drip edge should I use?
Metal Edge Drip: A drip edge has to be resistant to possible corrosion and should be 36 gauge or larger.
What is the difference between drip edge and gutter apron?
The most obvious attribute that distinguishes a gutter apron from a drip edge is the fact that a gutter apron is more of an L-shaped metal rather than a T. A gutter apron also comes in metal strips with aluminum and steel sheets. Like drip edge, a gutter apron may be available in many different colors.
When should you not use drip edge?
Just like normal drip edge, aluminum fascia and rake molding goes along the eaves and covers the edge of your roof’s deck to prevent water from going where it’s not supposed to. If your home has either one, you don’t need drip edge.
What nails do you use for drip edge?
The drip edge is nailed in place using 1-1/2 galvanized roofing nails. A felt-tip marker works great for marking cuts. And, again, prying open the end with a small flat bar allows the pieces to overlap cleanly.
