Table of Contents
How do you attach stair stringers to a deck?
How far apart should stringers be on deck stairs?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
Can I use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
Do you install risers or treads first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser.
How do I anchor my deck stairs to the ground?
How to Anchor Deck Stairs to Concrete Use your jigsaw. Notch out the bottom front of the center stair stringers to accept a 2×4 base plate. Make sure your stringers are level. Fasten the base plate to the stair stringers with screws. Locked in place.
Do deck stairs need footings?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How far apart should stair spindles be?
U.S. building codes mandate that balusters have no more than a 4-inch gap between them. This relatively tight amount of spacing still allows for visibility between spindles, but also stands as a safety measure to prevent small children from becoming stuck between spindles or from slipping through the balusters.
What is code for stair stringer spacing?
Cut stringers should be spaced no more than 18 inches on center. For example, a 36-inch-wide stairway should have three stringers. If the stairway is wider than 36 inches, four stringers should be installed.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
What is code for deck stairs?
Requirements for Deck Stairs Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back.
Do stair stringers need hangers?
Stringers support the steps of a stairway and fasten to the framing of the deck. The primary method of connection between a stringer and the framing is a stringer hanger. This metal bracket supports the stringer and holds it on the framing. Stringer hangers look like joist hangers and function in the same way.
Should I use nails or screws for stairs?
The answer is both. You should use nails to attach the deck’s joists and stair stringers to its framing. You should use screws to attach decking and railings to the framing.
How do you reinforce stair stringers?
One of the easiest methods of reinforcing your wood stair stringers is using 2×12 skirt boards along the outsides of your stairs. A skirt board is pretty much what it sounds like; triangular shaped wood that goes along the sides of your stair and hides all of the unsightly notched stringers and hardware.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
How far should a tread overhang the riser?
Stairs must have an overhang between 3/4″ to 1-1/4” to increase the depth of the step, making it better for descent while maintaining a clear 10-inch going for the ascent. Treads that are 11-inches deep or greater do not require an overhang.
Should you stain stair treads before installation?
Staining and varnishing hardwood treads prior to installation is recommended, especially in this case where we have stone or tile risers. Once the treads are stained and dried it’s time to cut and install them.
Can I use deck pier blocks instead of footings?
Pier blocks can be used instead of footings for a ground-level deck not requiring permits. Piers blocks can also be used if the frost level depth is less then the height of the pier block.
How deep should a footing be for stairs?
Dig a trench about 125mm deep for the footing for the first riser.
Do outdoor stairs have to have a landing?
All exterior staircases are required by code to have landings at the bottom and top to make sure it is safe and there is plenty of room for doors to swing, and for people to use. There are several pieces of building code to consider when building your deck stair landing.
Can I use 2×10 for deck stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
What size lumber do you use for stair risers?
Stair stringers are cut from 2×12 lumber. For exposed side stringers, use cedar lumber. Make one stringer for each 16 inches of stair width. Allow for light boxes if riser lights will be installed.
