Table of Contents
Do stairs need cove molding?
Cove moulding is typically installed on stairs underneath the nosing of the tread at the seam of the riser. It hides the small gaps created during construction, looks beautiful when finished.
What is cove molding for stairs?
Cove moulding (also spelled as “cove mold”) is a small decorative profile used underneath the bullnose of a stair tread against the top of the riser. Cove mould is typically installed in the same species as stair treads.
How do you install cove molding?
How to Install Plastic Cove Moulding Vacuum the edges of your floor where the wall and floor meet. Measure the length of the walls where you plan to install the cove moulding. Measure the length of the first wall, starting at an inside corner. Apply construction adhesive to the back side of the moulding in a wavy line.
What is a stair skirt?
The skirt is basically a piece of trim used to cover the structural section of the stairs. A skirt board is installed to the finished wall (sheet rock, paneling, etc.) once the open side of the stair has been finished.
What is Scotia molding?
Scotia is a decorative moulding used to cover the gap without removing the skirting. Scotia is fixed to the skirting board and over the top of the flooring around the perimeter of the wall. You would use Scotia if you were not putting your skirting on top of the wood floor.
What is shoe molding?
Paired with a baseboard and painted to match, shoe moulding (also called “base shoe”) is a thin strip of moulding that finishes out the look of baseboards. It can often be found in a curved or round shape similar to quarter round moulding.
What is the trim on the side of stairs called?
Skirtboard. A trimboard running with the rake, pitch or incline of the stair against the wall on the closed side of the staircase. While usually nonstructural, skirtboard protects the drywall surface and adds to the décor of the staircase.
What are stair brackets?
From simple contemporary designs to more elaborate styles, decorative stair brackets help to give a finished look to a set of stairs. Often found in historical homes of Edwardian and Victorian origin, stair brackets are experiencing a comeback as homeowners discover their elegant simplicity.
Do you put baseboards on stairs?
Install baseboard directly on top of stair stringers. Remember the stud pattern may change between floors, and there is no bottomplate to nail into. End the baseboard running down the stair stringer with a plumb cut flush with the end of the stringer.
What angle do you cut cove molding?
Cut 1/2 inch from the end of the molding at a 90-degree angle with a coping saw or a miter saw. This gives you the clean, sharp edge needed on the profile that enables you to cope it with precision.
What is the difference between crown molding and cove molding?
Cove molding performs the same function in the same place on the wall as crown molding. The main difference is the profile; cove molding has a concave profile, which bows inward, while crown molding has a convex, flatter appearance that projects out from the wall.
Do I need a skirt board on stairs?
You do not need a skirt board on stairs. If you don’t have baseboards in your house, then you don’t need skirting for your stairs. You might want stair skirting if you have baseboards in your house, as skirting will serve to connect, esthetically, baseboards on either ends of the step.
How much does it cost to install a stair skirt?
Hiring a handyman to install the skirting will cost about $30-$60 per hour or about $240-$480 per day, depending on location. Skirting for a single- or double-wide unit typically installs in one day, depending on size of home and level of ground.
Do you install stair treads or risers first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser. Treads and risers fasten with construction adhesive to the subfloor.
What is a stair Scotia?
Scotia Moulding – The timber moulding that sits around a cut string staircase. Spindles – Turned, carved or otherwise vertical sections placed between the handrail and the stair tread or string. Also known as balusters.
How do you stick Scotia?
To fit scotia using nails, secure into position by nailing the scotia to the skirting by spacing one nail every 30cm, ensure you don’t nail the scotia to the floor. To fit scotia using adhesive, apply grab adhesive to the back of the scotia and carefully apply to the wall, ensuring not to get any on your flooring.
What is difference between quarter round and shoe molding?
Shoe molding is much the same as quarter round, having the same 90° angle on the backside but instead of being a perfect quarter radius, its profile is a bit more squat. Using shoe molding gives the floor installer more latitude in their end cuts and also allows the trim carpenter to hide un-level floors.
