Table of Contents
Can you hang a closet rod in drywall?
Can You Hang a Closet Rod in Drywall? You can hang a closet rod in the drywall in such a fashion that it holds your clothing without pulling out of the wall. In order to do so, it’s best to use shelf support style brackets. These brackets can be set at any point along the back wall of your closet.
How do you hang a closet rod from the ceiling?
Draw a straight line on the ceiling at right angles to the joists using a yardstick or straightedge tool as your guide. Make the line the length of the closet rod you purchased for the project. Put the line at least 12 inches from the back wall of the closet to allow room to hang clothes hangers on the clothes rod.
How far from back wall should closet rod be?
As a rule, place the top rod 80 to 82-inches up from the floor and the bottom rod about 40-inches up from the floor. For a single rod application, plan 60-inches from the floor for placement. You will need at least 1-foot, 9-inches (24-inches is standard) away from the back wall for hanging.
Do closet rods need studs?
Installing a closet rod in a closet without conveniently located studs is a simple job that requires no special tools or advanced carpentry skills. Closet rods are typically held by flange-type sockets that are attached to the wall, screwed into framing studs.
Do closet rods need to go into studs?
Basic Installation It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.
Do closet walls have studs?
Closet shelves are usually anchored to the wall where the mounting screws can grab wall studs. If your walls are masonry, you likely don’t have studs at all. You’ll need the proper materials and methods to build a stud-free closet shelf.
Why does my closet rod keep falling?
However, if you’ve overloaded your closet rod by squeezing too many clothes into too small a space, or if it’s simply too thin for the job, it could sag in the middle.
How much weight can a wooden closet rod hold?
Never put more than 25-pounds of clothing on one of these rods or it will fail. The motorized version works with a remote control and can hold up to 60-pounds of clothing per rod.
How much weight should a closet rod hold?
Aluminum Anodized Elite 1-5/16”: Up to 80 lbs. Stainless Steel 1-1/16”: Up to 95 lbs. Steel Polished Chrome Round 1-1/16”: Up to 110 lbs. Steel Polished Chrome Round 1-5/16”: Up to 170 lbs.
How much space do you need between closet rods?
Standard rod height for a single closet rod is 60 inches, a height that leaves ample hanging space for floor-length dresses. When installing double rods, hang the top rod 80 inches from the floor and the bottom rod 40 inches from the floor. Leave at least 3 feet of space between the two rods.
Can a closet be 20 inches deep?
When designing a closet, consider the specific efficiencies of each different storage element to better serve your closet needs. The comfortable recommended depth of a closet is 24” (61 cm), but closet depths as narrow as 20” (50.8 cm) can be used if desired.
How much closet space do I need?
A standard full-size walk-in closet for two people should measure a minimum of 7 by 10 feet. It should preferably have an area of 100 sq. ft as this allows you to have storage units on all three walls with even a sitting area in the middle. In case you want a smaller one, small walk-ins can be built in as low as 25 sq.
Do Closets need headers?
Closet Door Headers As you might have guessed, even a closet doorway needs a header. No matter how light the door, window, shutter — or even if an opening is empty — you must frame it with king studs, jack studs, cripples (one every 16 inches) and a header.
How do you attach wood to drywall without studs?
If you are securing wood to drywall where no studs are backing the wall, or you don’t want to mar the appearance of your wood with screws, use a high-strength construction adhesive. Construction adhesive will bond the wood permanently to the drywall.
How do you frame a closet opening?
Complete DIY projects like a pro! Cut the top and bottom wall plates. Attach the top plate. Fasten the studs. Install the headers. Level the door jamb. Shim the side jamb until plumb and nail. Hang the doors. Strengthen the hinges.
What anchors to use in drywall?
The self-drilling anchor threads grip the drywall for a secure fit for drywall anchor installation. The anchor holds as the screw is twisted into place. Self-drilling anchors are made of plastic, nylon or metal. Self-drilling anchors are available in a wide range of weight ratings.
Can you screw straight into drywall?
Simple Answer: NO – A screw directly into drywall will not hold. You need to use some type of picture hanging hardware to hang a heavy picture securely. The threads of a screw into only drywall, without an anchor, will NOT permanently hold in the drywall. It will just pull right back out sooner or later.
