Table of Contents
Do you nail or screw Hardie board?
What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.
Do you have to pre drill cement board siding?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
Do you need plywood behind Hardie board?
Fiber cement siding should be installed over plywood, OSB, or sheathing. Building codes will usually require installing siding over water-resistant barriers and nailed into the studs every 16 or 24 inches.
What nails do you use for Hardie siding?
NAIL TYPE: Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
What goes behind Hardieboard?
Hardie™ Weather Barrier is installed over the sheathing—beneath the exterior siding—to reduce water and air infiltration. I’ve been using Hardie siding in the Texas heat for over 10 years. The homes I built then still look brand new today.
How do you attach things to Hardie board?
Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).
Do you caulk Hardie board siding?
James Hardie DOES NOT recommend using caulk or “H”-jointers for the butt joints of HardiePlank® siding with ColorPlus® technology. James Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2).
Do you need Thinset under Hardie board?
However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used. Thinset is going to create a solid surface under tile and prevent flexing that could lead to cracking.
Can you use a nail gun on Hardie board?
Overall, only two types of power nailers work best for attaching hardie siding: siding and roofing nailers. But if you must use a framing nailer, to install any James Hardie product, be sure to fit it with a quality flush mount attachment so as to control the depth the fastener is driven.
How do you cut holes in cement board siding?
To cut holes in cement backer board to use under tile, equip a portable jigsaw or sabre saw with a metal cutting blade. To start the saw in cement backer board, drill a hole though the backer board large enough for the jigsaw blade or make a plunge cut with the blade in the backer board.
What kind of screws do you use for cement board?
Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place.
Do backer board screws need flushing?
They should be flush or really close to it. Especially if you are painting over with a waterproofing membrane. I throw three backer screws in a sheet and then do pilot holes with a bit the size of my head about an 1/8″ in.
Do you need insulation under Hardie siding?
Hardie Plank is a cement board; it’s composition is sand and water. It is heavy on the wall and provides no insulation value. Formed to resemble wood, it fails to provide a deep, rich grain and does not come close to the look of wood. It is highly susceptible to mold and mildew.
Can Hardie board be nailed directly to studs?
GENERAL REQUIREMENTS: HardiePlank® lap siding can be installed over braced wood or steel studs spaced a maximum of 24″ o.c. or directly to minimum 7/16″ thick OSB sheathing. See General Fastening Requirements.
Can you screw into Hardie board siding?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. Fasteners shall be installed between 1 in. and 3/4 in.
Can you use a framing nailer for Hardie siding?
With some overlap in nail size, you may wonder whether framing nailers can be used for siding? The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing.
Do you caulk cement siding?
Many professionals, like those at James Hardie, also agree that you should not use caulk on fiber cement siding unless there is no metal flashing underneath. Flashing acts as a waterproofing layer for this type of siding, and caulking will prevent the flashing from doing its job.
Are drywall screws OK for cement board?
You don’t want to use regular drywall screws for cement boards. They can corrode, they can break down the edges of the boards, and they won’t drive in flush properly. Use ITW’s ROCK-ON and BACKER-ON screws instead.