Table of Contents
How do you put on a belt tensioner?
How to replace an accessory tensioner in 8 easy steps Draw a sketch or take a picture of the belt routing. Unload the belt from the tensioner by rotating the tensioner. Remove the old tensioner from the engine. Place the new tensioner on the engine.
How do you put a tensioner pulley back on?
Position the tensioner in the vise so you can access the pulley bolt. Turn the pulley bolt counterclockwise with a ratchet and a socket. Remove the bolt, the retaining washer and the pulley. Replace the pulley, washer and bolt and tighten to specified torque illustrated in the repair manual.
Can you replace a belt tensioner yourself?
Serpentine belt replacement is easy because today’s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
Should you replace tensioner with serpentine belt?
There is no recommended timeframe in which to replace your tensioner, especially as the belt itself usually needs replacing before the tensioner does. However, you should inspect your tensioner each time you service your car to monitor its condition and replace it if necessary.
Should you be able to move a belt tensioner by hand?
Appearance: Cycle the tensioner (mounted on the engine) through the entire range of motion (from stop to stop) by applying torque to the arm with a wrench. The tensioner arm should move smoothly and freely. Solution: If you notice a binding, sticking or grinding tensioner arm, the tensioner should be replaced.
Can you tighten a tensioner pulley?
Tighten the tensioner pulley by turning the adjustment bolt clockwise with the ratchet and socket until the belt is tight. Tighten the bolt in the center of the pulley with the ratchet and socket.
Is the tensioner pulley supposed to spin?
Checking the Tensioner Spin the pulley to see if it spins freely. If you hear grinding or the pulley doesn’t spin freely, replace the tensioner. When you replace the belt, it should take a lot of muscle power to move the tensioner. If you can move it easily, the spring tension is most likely not tight enough.
Is idler pulley same as tensioner?
The primary distinction between tensioners and idler pulleys is the presence of an adjustable bolt. Tensioners are positioned on the bolt through mounting. Idler pulleys are not mounted to an adjustable bolt. However, if bearings fail, tensioner and idler pulleys both require replacement.
Where is the belt tensioner located?
The belt tensioner is on the front of the engine, between the crankshaft and alternator pulleys.
How do I know if my belt tensioner is bad?
1. Grinding or squeaking noise from the belts or tensioner. The most common symptom of a bad or failing drive belt tensioner is noise from the belts or tensioner. If the tensioner is loose the belts may squeak or squeal, especially when the engine is first started.
How long does it take to replace a belt tensioner?
It should only take about an hour of work for the replacement, but sometimes it can be more, which can drive up the labor costs, and that varies from one car to the next.
Can you adjust an automatic belt tensioner?
Not all types of drive belt systems can be adjusted. Cars equipped with an automatic belt tensioner adjust themselves over time and do not require adjustment.
Should I replace tensioner or just pulley?
If the pulley is damaged, replace the tensioner assembly not just the pulley.
Why is my belt tensioner shaking?
Causes of Belt Tensioner Wobbling In general, belt tensioners tend to get noisy when they fail. If your belt tensioner is chirping or makes other noises, it is often an indication that the part is old and needs to be replaced. You can even remove the belt, spin each pulley, and listen for rumbling or other noises.
What does a bad tensioner sound like?
Symptom 1: Squealing, rattling, or chirping. When the tensioner or tensioner pulley fails, the loss of tension can cause the belt and pulleys to make high-pitched rattling or chirping noises. If the pulley bearing completely fails, it can also cause a squealing or even a grinding noise.
Can a bad tensioner cause engine vibration?
Grinding noises – Grinding and rumbling noises are another common sign of tensioner or idler pulley failure, usually due to failing bearings. Excessive tensioner movement – Worn-out coil springs can also cause drive belt tensioners to loosen their grip on the drive belt, resulting in excessive vibration and rattling.
Can a bad belt tensioner cause misfire?
The belt may oscillate between too little tension and too much tension. The belt will slip and catch, causing noise and vibration. This can cause a change in crankshaft speed that can be severe enough to cause the engine management system to think that a misfire just occurred.
What happens if the tensioner pulley fails?
When the tensioner or tensioner pulley fails, the loss of tension can cause the belt and pulleys to make high-pitched rattling or chirping noises. If the pulley bearing completely fails, it can also cause a squealing or even a grinding noise. Symptom 2: Knocking or slapping. This can cause a slapping or knocking noise.
How tight should the belt tensioner be?
A general rule of thumb for the correct tightness is being able to twist a belt with a thumb and finger a 1/2 turn and feel resistance. If you can turn it more than a 1/2 turn, you do not have enough tension on the belt. If you cannot turn it a 1/2 turn, you have too much tension on the belt.
How tight should a tensioner pulley be?
When twisted either way from the middle, the tension in the belt must not be more than 12 inch. The belt is too tight if it is twisted more. The positions do not work for the vehicle.
How do you tighten a belt tensioner?
Locate the adjuster bolt on the belt tensioner used to secure the serpentine belt, and adjust the tension by loosening or tightening the adjuster bolt with a racthet and socket while you simultaneously move the belt back and forth gently to find the proper tension.
