Table of Contents
Plan the space for your tap. Lay out the beer lines and CO2 canister. Add holes in the refrigerator, if needed. Drill a hole for the beer tap. Connect the regulator to the CO2 tank. Connect the coupler to the top of the keg. Run the hose from the refrigerator to the underside of the tap. Open the CO2 cannister.
How much does it cost to get a beer tap installed?
A typical 20 beer tap wall installation will cost $20,757 with an average return on investment of less than 4 months based on extra revenue generated by your self-pour taps.
How do you make a beer tap at home?
Plan the space for your tap. Lay out the beer lines and CO2 canister. Add holes in the refrigerator, if needed. Drill a hole for the beer tap. Connect the regulator to the CO2 tank. Connect the coupler to the top of the keg. Run the hose from the refrigerator to the underside of the tap. Open the CO2 cannister.
How much does a keg cooler cost?
The cost of the kegerator or refrigeration unit ranges from $1,500 to $5,000 depending on capacity. Make sure you establish whether the following items are included: Dispense tower. Drip tray.
What do I need to build a keezer?
The most basic materials you’ll need to build your own keezer is: Chest freezer, minimum of 7.0 cu. Temperature controller such as an Inkbird. Enough 2×6 (or 2×8 or 2×10) non-treated wood to go around the freezer’s top, called a “collar” Enough taps, CO2 regulators, CO2 manifolds and lots of vinyl or silicone tubing.
What do I need to have a keg at home?
“It’s simple,” Suto said. “All you really need is a drill and basic tools: a screwdriver and a wrench. It’s a low-skill operation. Getting beer on draft isn’t that hard.” Your local brewer will be happy to sell you a keg and charge the CO2 tank that comes with the kit.
How do you run a beer line through a wall?
Wrap the beer and glycol lines in mylar bubble wrap and then heavy foam pipe insulation. Insulation – a product that is a combination of mylar and air bubble wrap is a good choice for insulating beer lines for short runs. Double wrap this material around the beer line(s), with some foam pipe insulation around that.
How much does a keg cost?
Consider that the average cost for a standard half barrel keg of Budweiser is approximately $100. A standard keg contains 15.5 gallons, or 1,984 ounces.Why Buy a Kegerator? Budweiser: Average Cost of Half Barrel Keg $103.75 Average Cost of Case $23.50 No. Cases Needed by Volume to Equal Keg 6.88.
How many kegs fit in a walk in cooler?
How Many Kegs Fit in a Walk-In Cooler? Polar King has the ability to fully customize nearly every aspect of a walk-in cooler or walk-in freezer. In Gnometown Brewery’s case, this 7’x16′ commercial beer cooler will fit approximately 40 double stacked kegs.
How do you keep a keg cold at a wedding?
The cheapest way to keep a keg cold is by placing it in a suitable container and covering it with ice. Place the keg in the tub, surround it with ice and then top up with cold water. You can then either connect a pressure regulator and beer lines or fit a picnic tap directly to the keg.
How often should draft beer lines be replaced?
How often should you replace your beer lines? Well, about once a year is fine as long as you keep up with your cleaning. Recirculating BLC through your lines once every two weeks should do a good job of keeping them clean.
Do you leave the CO2 on in a Kegerator?
To be on the safe side, we always recommend shutting off the CO2 when you do not have a keg hooked up. Technically speaking, the components of a kegerator will not allow CO2 passed the coupler when it is not hooked to a keg.
How do you set up a beer keg?
Getting started Clamp down the keg coupler to start the beer flow. Turn on the cooler. Turn dial on the top of the gas bottle anti-clockwise to start gas flow, one turn is fine. Turn on cooler at the plug and pour half a pint of product immediately.
How do I know what keg coupler I need?
To choose the correct coupler for your home use, you must know the brand/style of beer you serve, know where it was brewed and/or the size of keg it is in. This is because there are six different types of keg couplers.
How do you hook up a gas keg?
Turn the gas bottle on and set pressure on regulator to 40 PSI or 280 KPA, hold the lid in place and connect the gas line to the keg. Allow the pressure of the gas to seal the keg and then clip the lid down.
Can I drill a hole in my fridge?
Drilling into side is not safe. A coolant tube may or may not be there, but you will mess up the thermal insulation for sure, creating dew point and similar problems.
Can you put a keg in the fridge?
Draft beer should be stored and dispensed at 36-40 degrees F. Keeping a thermometer inside the fridge is always a good idea. If your keg has been handled a great deal or has warmed up, it may take several hours to settle down and cool before pouring. So be sure to give your beer time to rest.
Why is my beer tap loose?
If you find that your beer faucet feels loose or is visibly loose, it is not broken. The faucet attaches to a shank that goes through the beer tower. Under the cap on the top of that beer tower is a nut. Sometimes those work themselves loose and just need to be tightened up.
Why is beer tap leaking?
Dripping from the Spout (Type 1) The interior seal (also called the valve seat or shaft seat) is worn out or degraded. In the most common beer faucets used in kegerators and commercial tap systems, the seal is a simple rubber washer.
