Table of Contents
How much does it cost to install a tub shower combo?
Installing a tub-shower combo costs $1,400 to $4,000, depending on if it’s a prefab tub-shower stall or a separate tub and shower surround. Having at least one bathtub in the home increases resale value. Bathtub replacement costs $600 to $2,500 on average for a basic alcove tub.
How long is a tub shower combo?
Most bathtub and shower combos come standard and are 60 inches by 30 inches by 72 inches or 60 inches by 36 inches by 72 inches. This includes a 60-inch basin length, 30 or 36-inch basin width, and 60-inch wall width.
What is a shower tub combo?
Tub/Shower Combos. A space-saving combination tub-shower is a smart choice. These two-in-one units make the most of limited space by providing all the benefits of both a shower and a bathtub in a compact footprint, which can be particularly useful in a child’s or guest bathroom.
What does it cost to have a bathtub installed?
The average cost to install a bathtub is $4,681, but can range from $1,583 and $7,812, depending on the type of tub and modifications needed. The average cost of the tub itself ranges from $200 to $8,500 or more.
Do you need cement board behind tub surround?
ANSWER – No there should not be a gap between the top of the bathtub flange and the backer board on the wall. There should be a moisture barrier behind the backer board that is installed in a weather lapping manner starting at the tub flange working up the wall.
What goes behind cement board in shower?
Unless specifically manufactured as a waterproof product, cement board is water resistant but not waterproof. You must coat it with a fluid-applied waterproofing or apply a water-resistant barrier behind it that drains (BSC 2009b).
Do you install a tub before or after drywall?
Fiberglass and acrylic tub and shower enclosures come with a flanged edge that attaches directly to the wall studs, and the proper way to hide this flange is to install drywall over it. Consequently, enclosures are typically installed on the bare studs.
Can you glue a tub surround to cement board?
Recommended For: adhering plastic and fiberglass tub and shower surrounds to structurally sound drywall, plywood, ceramic tiles, greenboard and cement backerboard.
How many tubes of glue do I need for a tub surround?
Application Instructions: A typical surround will require approximately 3 tubes of adhesive for installation.
Can you install a tub surround over drywall?
The short answer to the question is, “It’s not recommended.” However, this answer only really only suffices if you’re converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.
Can you put a tub surround over existing tub?
Tub surrounds can sometimes be installed over existing tile, but only when conditions are right. The old tile area needs to be smaller than the kit and you’ll need to build up the surrounding wall to the level of the tile, usually with 1/4-in. drywall. First, tape cardboard over the tub to protect it.
What goes behind shower walls?
Rigid air barrier materials for use behind showers and tubs include fiber-cement, fiber-reinforced gypsum, glass mat gypsum, or fiber mat-reinforced cementitious backer panels.
What is the best adhesive for a tub surround?
Loctite® PL® 550 Tub Surround Adhesive is specially formulated to bond most plastic bathroom and shower enclosures. It is unaffected by moisture, steam, water, heat or cold when fully cured. PL 550 Tub Surround Adhesive will not harm or burn-through tub kit materials if used as directed.
What is the best glue for a shower surround?
Loctite PL 550 Tub Surround Adhesive is designed to bond most bathroom and shower enclosures without harming or burning the tub kit materials. Our water-based adhesive is perfect for this task because it resists moisture, steam, water, heat, and cold when fully cured.
What is the rough opening for a tub shower combo?
The standard rough-in dimension for a bathtub is 60-¼”. But if there’s a gap, you can attach furring strips to the stud wall. You can also apply some cement or plywood.
What is the difference between a soaking tub and regular tub?
Deeper than the average bathtub, soaking tubs are designed to offer the ultimate in relaxation by allowing you to fully submerge. When it comes to size, soaking tubs blow regular tubs out of the water, with some topping out at 90 inches in length and 76 inches in width—big enough to accommodate two bathers.
Is a shower tub combo a good idea?
Tub-and-shower combinations offer a great combination of spaciousness and style, and they’re the most common of all bathtub installations—found in about 65 percent of homes today. These two-in-one pieces are affordable, sturdy, and easy to install, and they make good use of limited bathroom space.
Can you have a walk in tub with a shower?
Generally walk-in tubs are put in the place of the existing bathtub. Walk in tubs work best for those that like to bath, but want to have the option for a standup or seated shower too. If you only shower, consider an accessible shower with a seat instead.
