Table of Contents
Do you need to install backer board for floor tile?
Whenever you’re laying tile on a wood subfloor, you need to first install cement backerboard to prevent leaks and water damage that could harm your flooring and the structure of your home. Unlike wood or drywall sub-surfaces, cement backerboard will not rot, warp or grow mold and mildew when exposed to water.
Do you have to use thinset under backer board?
Using thinset under cement board is a commonly skipped step amongst many contractors. However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used.
How thick should cement board be under tile floor?
Floors: A 1/4-inch minimum thickness is needed, but thicker panels are also fine. Walls: Use 1/2-inch or 5/8-inch-thick cement board, not 1/4-inch. The extra thickness is needed when spanning the studs and it provides a solid base for the tile.
Can I just screw down cement board?
Screw and Joints Do not use drywall screws as they are not recommended to be used to hold the backer board in place. All of your backer board pieces should be cut before they are placed on the floor. It is important to highlight that screws shall not be installed all the way down to the floor joists.
Which backer board is best for floors?
Half-inch cement backer board is ideal for most tiling jobs, including walls, floors, countertops, and ceilings. For flooring, the backer board should be installed over a 5/8-inch thick OSB or plywood base. For countertops, use 3/4-inch plywood beneath the backer board.
How long after backer board can I tile?
However, after you mount the backer board to the floor you simply have to seal the seams with mortar and wait until the mortar dries. This is normally 12 hours but may be up to 24 hours in some cases. After the mortar is dry the backer board is ready to receive the mortar for the tile.
Can you install cement board without thinset?
Installing cement board over a concrete subfloor. Not only is thinset a critical component underneath cement board but the other critical component is the fasteners. And you won’t have the fasteners if you are trying to install it over concrete.
How thick should thinset be under Backerboard?
How much thickness will thinset add? The thin set under the backer board may account for about 1/16″. The bond coat for the tiles about 3/32 – 1/8″. Your best bet is to use 1/4″ which should end up being 5/16″, standard thickness tiles can average about 3/8″ installed, plus or minus.
Do you have to tape cement board before tiling?
If you are going to tile over the cement board, you should tape the seams. This should not be that difficult. Pack in thinset, lay on the tape, and flat-knife to get it set in. In the corners, use a corner knife.
How important is thinset under Hardibacker?
It will make an enormous mess under the house (or whatever is under your bathroom). It is also more likely to make the floor uneven since it is hard to level thinset that is separated by gaps. The installation manual for HardieBacker suggests to embed it in thin-set and it should be installed over plywood.
What do you do with a gap between tub and cement board?
Ideally, you would leave a 1/8 inch gap which would then have the sealant applied to it. Either stopping the cement board above the tub flange or alternately shimming it out and dropping it down near the tub would both be good options.
Does shower wall tile need backer board?
You don’t need to use a backer board in the entire bathroom, just in the wet shower area. Choose a backer board that’s the same thickness as the drywall so you have a seamless transition from one to the other.
How thick is backer board for tile?
Cement backer board comes in two standard thicknesses, 1/2 inch and 1/4 inch. The industry standard is to use 1/2-inch-thick backer board on wall tile installations, such as a tub surround.
Can you put tile directly on drywall?
As long as your wall is smooth and flat, you can install a ceramic tile kitchen backsplash directly over drywall or plaster with no problem. Start by cleaning the wall to remove any grease, then apply thin-set adhesive, and set the tile. After the adhesive has set, apply grout, and you’re done.
Can you walk on cement backer board?
Some cement boards are “softer” than others, so dragging a refridge over it will crush or damage some. the main thing is just be carefull of it. Thank you.
How long should Thinset dry before tiling?
24 to 48 Hours You should wait at least 24 hours before grouting the tiles. You may notice that the edges of the thinset or the thinset showing through the grout lines looks dry. Don’t be fooled by this. The thinset under the tiles isn’t receiving as much air as the edges and is therefor not fully cured.
Which side of cement board faces out?
Cement board has a smooth side and a rough side. Face the rough side out if you will be using thin-set mortar adhesive to install the tile but the smooth side out if you will be using latex mastic.
What kind of Thinset goes under cement board?
An unmodified thinset (Masterblend) is fine between the Hardi and the subfloor. Tara, The reason for the layer of thinset between the cement board and the subfloor is to fill the voids/gaps between the two. It’ll keep the cement board from moving up and down.
Can you use Liquid Nails on cement board?
Can I use liquid nails or glue with HardieBacker® cement board? No. ”Liquid Nails” is not a bonding mortar. It is a structural adhesive generally used to bond the subfloor to the floor joists just prior to nailing.
