Table of Contents
Do I need thinset under backer board?
However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used. Thinset is going to create a solid surface under tile and prevent flexing that could lead to cracking.
Do I need cement board under ceramic tile?
What you need for a tile base. If you want to replace an old, cracked tile floor or other type of flooring with new ceramic tile, it’s absolutely imperative that you create a solid setting base for the new tile. If you’re working over a wood subfloor, cement board is the right choice for your tile base.
Can I just screw down cement board?
Screw and Joints Do not use drywall screws as they are not recommended to be used to hold the backer board in place. All of your backer board pieces should be cut before they are placed on the floor. It is important to highlight that screws shall not be installed all the way down to the floor joists.
How thick should cement board be under tile floor?
Floors: A 1/4-inch minimum thickness is needed, but thicker panels are also fine. Walls: Use 1/2-inch or 5/8-inch-thick cement board, not 1/4-inch. The extra thickness is needed when spanning the studs and it provides a solid base for the tile.
Is backer board necessary for tile floor?
Whenever you’re laying tile on a wood subfloor, you need to first install cement backerboard to prevent leaks and water damage that could harm your flooring and the structure of your home. Unlike wood or drywall sub-surfaces, cement backerboard will not rot, warp or grow mold and mildew when exposed to water.
How important is thinset under Hardibacker?
It will make an enormous mess under the house (or whatever is under your bathroom). It is also more likely to make the floor uneven since it is hard to level thinset that is separated by gaps. The installation manual for HardieBacker suggests to embed it in thin-set and it should be installed over plywood.
What kind of thinset goes under cement board?
An unmodified thinset (Masterblend) is fine between the Hardi and the subfloor. Tara, The reason for the layer of thinset between the cement board and the subfloor is to fill the voids/gaps between the two. It’ll keep the cement board from moving up and down.
What do you put under Hardibacker?
Latex or acrylic modified thinset (complying with ANSI A118. 4). Dry-set mortar for use between subfloor and cement board only (complying with ANSI A118.
What kind of subfloor is needed for ceramic tile?
Exterior-Grade Plywood Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.
Can you put tile on drywall?
As long as your wall is smooth and flat, you can install a ceramic tile kitchen backsplash directly over drywall or plaster with no problem. Start by cleaning the wall to remove any grease, then apply thin-set adhesive, and set the tile. After the adhesive has set, apply grout, and you’re done.
Can you install tile directly on plywood?
Tile can be laid on plywood. But do not install tile directly on the plywood subfloor itself. Use an intervening layer of a sheet of thinner plywood.
How many screws do I need for cement board?
Hang the cement boards cement board to the back wall. Place special 1-1/4 in. cement board screws every 8 in. along each stud but 1 in.
How thick is backer board for tile?
Cement backer board comes in two standard thicknesses, 1/2 inch and 1/4 inch. The industry standard is to use 1/2-inch-thick backer board on wall tile installations, such as a tub surround.
How thick should tile subfloor be?
The subfloor under the tile should be at least 1 1/8″ thick, with a minimum of 5/8″ thick exterior grade plywood topped by 1/2″ cement backer board.
Can I use 1/4 cement board on floors?
Both 1/4- and1/2-inch cement board are appropriate for floors. To install cement board on floors, cement board manufacturers mandate a 5/8-inch plywood subfloor or OSB underlayment. They also require a 3/4-inch subfloor where tile size exceeds 12 inches.
Can I install tile without backer board?
As long as a concrete slab is very flat and contains no cracks, tile can be installed directly on top, using thinset as the adhesive, allowing you to skip the backer board layer. If the slab is uneven or cracked, it must first be patched and leveled before tile can be installed.
Can I tile directly onto wood?
Tiling on wood. Can you tile on wood? Yes, but because wooden floors naturally bend, bounce and expand, tiles can end up cracking under the pressure if installed incorrectly. Tiling on wood surfaces is all about ensuring there is enough rigidity in the wooden subfloor and selecting the correct flexible tile adhesive.
Why do you have to use cement board under tile?
Most importantly, cement backer board contributes to a longer-lasting, more durable tile installation, with no chance of backing board rot and a reduced chance of rot with the underlying wall studs or floor joists.
How do you apply thinset under Backerboard?
Scoop up thinset on the flat edge of a 1/4-inch, square-notched trowel and spread the thinset across the plywood. Cover an area large enough to place the first backer board sheet. Apply another layer of thinset over the first, using the square-notched edge of the trowel.
Can you install Hardie board over OSB?
In this case the thinset is used to fill all the voids between the hardie and osb, not to bond them together. The mechanical fasteners will hold the two together. No problem here using thinset and osb. It will probably be OK.
