Table of Contents
Where should the expansion tank be installed?
An expansion tank is generally installed directly above the water heater by means of a tee-fitting installed in the cold water delivery pipe. The expansion tank is usually installed vertically, though it is acceptable to install it horizontally if it is necessary because of space limitations.
How do you install expansion tank on a hot water heater?
How to Install Water Heater Expansion Tank Step 1: Disconnect the Water and Power Supply. Step 2: Bring Out Expansion Tank and Accessories. Step 3: Confirm the Water Supply Line for Cold Water. Step 4: Install the Expansion Tank. Step 5: Attach the Heater Tank. Step 6: Restore the Water and Power Supply to the Heater.
Do I need to install an expansion tank on my water heater?
An expansion tank is always highly recommended if you have a ‘closed-loop system’ caused by any kind of check valve or pressure regulating valve installed on your house’s water supply line. However, the long-term wear and tear of this excess pressure can reduce the life expectancy of everything in your plumbing system.
Does it matter which way an expansion tank is installed?
Expansion tanks can be installed in any direction. Whether oriented uprightly, horizontally, or even upside down, the expansion tank will function properly without any adverse effects. When putting an expansion in an abnormal position (specifically sideways or horizontally), make sure to support the tank.
How close should an expansion tank be to a water heater?
The items which should be installed in sequence in the cold water line are (1) the EXPANSION TANK must be installed at least 18 inches away from the cold water inlet fitting on the water heater, (2) the PRESSURE GAUGE, and (3) the PRESSURE REDUCING VALVE, if required, see Figure 1.
What pressure should my expansion tank be set at?
The recommended water pressure is between 50 and 60 PSI. Thermal Expansion Tanks contain an air bladder which is pressurized with air, and expands and contracts to absorb the expanded water from the water heater. needed. Check the air pressure in the Expansion Tank using a tire gauge.
What size expansion tank do I need for a 40 gallon water heater?
General Guidelines for Sizing an Expansion Tank Water Heater Capacity Supply Pressure (psi) Expansion Tank Size 40 to 60-gallon 40-50 psi 2-gallon 40 to 60-gallon 60-80 psi 3.2-gallon 80-gallon 40 psi 2-gallon 80-gallon 50-60 psi 3.2-gallon.
How much does it cost to install an expansion tank on a water heater?
$145 – $350, Installed The cost to install a water heater expansion tank ranges from $55 and up for the rare DIY project, to about $350 when a pro adds an expansion tank to a large residential water heater.
Why is the expansion tank on the cold side?
One expansion tank manufacturer states: “We recommend the cold water side installation because the tank is not insulated. When the expanded volume enters the tank, it will cool down. With the tank on the cold water side, this expanded volume will pass through the water heater before going out to the faucets.”Feb 28, 2010.
What can I use instead of a expansion tank?
The Thermal Expansion Relief Valve can replace a water heater expansion tank because it functions similarly. Both products absorb the excess pressure in the plumbing system created by thermal expansion.
Can a water heater expansion tank be installed horizontally?
Can a water heater thermal expansion tank be installed sideways/horizontally? Most expansion tanks are designed to be installed vertically (stem up or stem down). You can install one sideways, but it will shorten the lifespan unless it is designed and specified by the manufacturer for horizontal installation.
What happens if expansion tank is full?
Pre-charge pressure that’s too low may be indicated when the tank is full of water. Low pressure can cause too much water from entering the tank. It could also indicate that the diaphragm is no longer functional, which means that there is nothing to prevent the water from entering.
Does the expansion tank go on the hot or cold side?
Although expansion tanks can be installed on the hot side, we strongly recommend they be installed on the cold line, downstream of the shutoff valve.
Should an expansion tank be vertical or horizontal?
Do mount tank vertically with connection at top: It is also best to install diaphragm type expansion tanks vertically with the piping connection at the top. This reduces stress on the tank’s connection relative to horizontal mounting.
Should expansion tank be supported?
All expansion tanks (even the small 2-gallon tanks) should be supported in some way. You want to match the pressure in the expansion tank as close as possible to the water pressure of the house.
Will an expansion tank increase water pressure?
The expansion tank contains air, which is highly compressible. Expanding water from the water heater can flow into the expansion tank, where the air compresses, making room for the increased volume of water. Water pressure in the system doesn’t increase significantly.
What size expansion tank do I need?
As a general rule, the bigger the water heater, the bigger the expansion tank. For a 50-gallon water heater, you require a 2-gallon expansion tank. Depending on how high your water pressure is, however, you may need to go up a size to a 4.5-gallon expansion tank.
Can I install expansion tank with PEX?
Connect Tank to Tee Cut a piece of PEX to run between the expansion tank and the tee-fitting that you inserted in the hot water tank cold water supply line. If you have other fittings between the two, you will need to cut pieces of PEX to connect those as well.
How do I know if my expansion tank is working?
The tank should be full of air and therefore sound hollow. If it makes a dull thud rather than a hollow sound, your tank is full of water and needs repair or replacement. You can also gauge this by feeling the tank, which will be cool where it’s holding air and warm where it’s holding water.
